LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2004 >> CTS Base, 3.2 N >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 13 (Engine Mechanical - 3.6L (Ly7) (Repair Procedures -- 1 Of 5)) >> On-Vehicle Repair Instructions - Part 1 >> Engine Support Fixture >> Installation Procedure

Installation Procedure

WARNING: This page is about a different variant/trim than selected.
    Fig 1: Installing Engine Lift Bracket To Front Of the Right (Bank 1) Cylinder Head
    GM1338595Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in Cautions and Notices.
  1. Use a grade 10.9, M10 X 1.5 X 35 bolt (GM P/N 11519182 or equivalent) in order to install an engine lift bracket (OTC #7100, J 36857  or equivalent) to the front of the right (Bank 1) cylinder head in the location shown.

    Tighten:  Tighten the bolt to 65 N.m (48 lb ft).

  2. Remove the electrical connector bolt and the electrical connector from the rear of the left cylinder head.
    3. Fig 2: Installing Engine Lift Bracket To Rear Of the Left (Bank 2) Cylinder Head
    GM1338596Courtesy of GENERAL MOTORS CORP.
  3. Use a grade 10.9, M10 X 1.5 X 35 bolt (GM P/N 11519182 or equivalent) in order to install an engine lift bracket (OTC #7100, J 36857  or equivalent) to the rear of the left (Bank 2) cylinder head in the location shown.

    Tighten:  Tighten the bolt to 65 N.m (48 lb ft).

    4. Fig 3: Identifying J 28467-B & J 28467-3
    GM790666Courtesy of GENERAL MOTORS CORP.
  4. Loosely install the J 28467-501  (1) to the ends of the strut tower tube J 28467-3 (2).
    5. Fig 4: Placing Strut Tower Tube J 28467-3 & J 28467-501 On Top Of Both Left & Right Fender Lips
    GM790668Courtesy of GENERAL MOTORS CORP.
  5. Place the strut tower tube J 28467-3 and the J 28467-501  on top of both the left and right fender lips, over the engine rear lift bracket.
    6. Fig 5: Installing Radiator Shelf Tube J 28467-2A On Top OF Strut Tower Tube J 28467-3 Above Engine Front (Right Back) Lift Bracket
    GM790672Courtesy of GENERAL MOTORS CORP.
  6. Install the radiator shelf tube J 28467-2A (2) on top of the strut tower tube J 28467-3 (1) above the engine front (right bank) lift bracket.
    7. Fig 6: Installing Quick Release Pin J 28467-9
    GM405958Courtesy of GENERAL MOTORS CORP.
  7. Install the round tube of the front support assembly J 28467-4A through the large hole in the radiator shelf tube J 28467-2A.
  8. Remove the upper tie bar cover.
  9. Locate the J 28467-4A front support assembly to the upper tie bar.
  10. Install the J 28467-9 7/16 in x 2.0 in quick-release pin through the top hole in the J 28467-4A front support assembly.
    11. Fig 7: Installing J 28467-1A Cross Bracket Assembly
    GM287864Courtesy of GENERAL MOTORS CORP.
  11. Install the J 28467-1A cross bracket assembly.
  12. Hand tighten the J 28467-1A cross bracket wing nuts.
    13. Fig 8: View Of Lift Hook Assembly
    GM682139Courtesy of GENERAL MOTORS CORP.
  13. Install the J 28467-7A bolt hook through the J 28467-6A bracket.
  14. Install the J 28467-34 lift hook wing nut and washer to the J 28467-7A lift hook.
  15. Repeat the previous two steps in order to assemble two lift hooks and brackets.
    16. Fig 9: View Of Lift Hook & Bracket Assembly At Longitudinal Mounted Cross Bar
    GM682301Courtesy of GENERAL MOTORS CORP.
  16. Install one of the lift hook and bracket assemblies (1) to the J 28467-3 strut tower tube (2) above the engine rear lift bracket.
  17. Install the lift hook J 28467-7A through the engine rear lift bracket. Ensure the hook does not damage adjacent components.
  18. Install the other lift hook and bracket assembly (1) to the J 28467-2A radiator shelf tube (2) above the engine front lift bracket.
  19. Install the lift hook J 28467-7A through the engine front lift bracket. Ensure the hook does not damage adjacent components.
  20. Hand tighten the lift hook wing nuts J 28467-34 in order to remove all slack from the engine support fixture assembly.
scientia non olet · About LEMON Manuals