LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2015 >> Verano Leather >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 8 (Engine Controls And Fuel - 2.0L (LHU) - DTC P0010 To P0246) >> Diagnostic Information and Procedures >> DTC P0237 or P0238: Turbocharger Boost Sensor >> Circuit/System Testing

Circuit/System Testing

WARNING: This page is about a different variant/trim than selected.
  1. Ignition OFF, and all vehicle systems OFF, disconnect the harness connector at the B111B Turbocharger Boost/Intake Air Temperature Sensor. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 5 Ω between the low reference circuit terminal 1 and ground.
    • If 5 Ω or greater 
    1. Ignition OFF, disconnect the X1 harness connector at the K20 Engine Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If less than 5 Ω 
  3. Ignition ON.
  4. Test for 4.8-5.2 V between the 5 V reference circuit terminal 3 and ground.
    • If less than 4.8 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
      NOTE:

      If the signal circuit is shorted to a voltage the engine control module or the sensor may be damaged.

    • If greater than 5.2 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If between 4.8-5.2 V 
  5. Verify the scan tool Boost Pressure Sensor voltage parameter is less than 0.2 V.
    • If 0.2 V or greater 
    1. Ignition OFF, disconnect the X1 harness connector at the K20 Engine Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit terminal 4 and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K20 Engine Control Module.
    • If less than 0.2 V 
  6. Install a 3 A fused jumper wire between the signal circuit terminal 4 and the 5 V reference circuit terminal 3.
  7. Verify the scan tool Boost Pressure Sensor voltage parameter is greater than 4.5 V.
    • If 4.5 V or less 
    1. Ignition OFF, disconnect the X1 harness connector at the K20 Engine Control Module.
    2. Test for infinite resistance between the signal circuit terminal 4 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open or high resistance in the circuit.
      • If less than 2 Ω, replace the K20 Engine Control Module.
    • If greater than 4.5 V 
  8. Test or replace the B111B Turbocharger Boost/Intake Air Temperature Sensor.
scientia non olet · About LEMON Manuals