LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2015 >> Regal GS, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Steering Column Switches >> Secondary And Configurable Customer Control System >> Diagnostic Information and Procedures >> Steering Wheel Controls Malfunction >> Circuit/System Testing

Circuit/System Testing

All Controls Malfunction

  1. Ignition OFF, disconnect the harness connector at the S70R Steering Wheel Controls Switch - Right. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10Ω between the ground circuit terminal 2 and ground.
    • If greater than 10Ω 
    1. Ignition OFF.
    2. Test for less than 2Ω in the ground circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, repair the open/high resistance in the ground connection.
    • If less than 10Ω 
  3. Ignition ON.
  4. Verify that a test lamp illuminates between the B+ circuit terminal 8 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2Ω in the control circuit end to end.
      • If greater than 2Ω, repair the open/high resistance in the circuit.
      • If less than 2Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit terminal 8 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S70R Steering Wheel Controls Switch - Right.
    • If the test lamp illuminates 
  5. Test for 2-10V between the serial data circuit terminal 7 and ground.
    • If less than 2V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster.
    2. Test for infinite resistance between the serial data circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2Ω in the serial data circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, replace the P16 Instrument Cluster.
    • If greater than 10V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster, ignition ON.
    2. Test for less than 1V between the serial data circuit and ground.
      • If 1V or greater, repair the short to voltage on the circuit.
      • If less than 1V, replace the P16 Instrument Cluster.
      • If between 2-10V 
  6. Test or replace S70R Steering Wheel Controls Switch - Right

S70R Steering Wheel Controls Switch - Right Malfunction with UV6

  1. Ignition OFF, disconnect the harness connector at the S70R Steering Wheel Controls Switch - Right. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10Ω between the ground circuit terminal 2 and ground.
    • If greater than 10Ω 
    1. Ignition OFF, test for less than 2Ω in the ground circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, repair the open/high resistance in the ground connection.
    • If less than 10Ω 
  3. Ignition ON.
  4. Verify that a test lamp illuminates between the B+ circuit terminal 8 and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2Ω in the control circuit end to end.
      • If greater than 2Ω, repair the open/high resistance in the circuit.
      • If less than 2Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit terminal 8 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the S70R Steering Wheel Controls Switch - Right.
    • If the test lamp illuminates 
  5. Ignition OFF, disconnect the harness connector at the P29 Head-Up Display, ignition ON.
  6. Test for 2-10V between the S70R Steering Wheel Controls Switch - Right serial data circuit terminal 7 and ground.
    • If less than 2V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster.
    2. Test for infinite resistance between the S70R Steering Wheel Controls Switch - Right serial data circuit terminal 7 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for infinite resistance between the P29 Head-Up Display serial data circuit terminal 1 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    4. Test for less than 2Ω in the S70R Steering Wheel Controls Switch - Right serial data circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, replace the P16 Instrument Cluster.
    • If greater than 10V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster, ignition ON.
    2. Test for less than 1V between the S70R Steering Wheel Controls Switch - Right serial data circuit terminal 7 and ground.
      • If 1V or greater, repair the short to voltage on the circuit.
      • If less than 1V.
    3. Test for less than 1V between the P29 Head-Up Display serial data circuit terminal 1 serial data circuit terminal 1 and ground.
      • If 1V or greater, repair the short to voltage on the circuit.
      • If less than 1V, replace the P16 Instrument Cluster.
      • If between 2-10V 
  7. Connect the harness connector at the S70R Steering Wheel Controls Switch - Right. Ignition ON.
  8. Verify steering wheel controls function properly.
    • If steering wheel controls function properly 

      Replace P29 Head-Up Display.

    • If steering wheel controls do not function properly 
  9. Ignition OFF. Disconnect harness connector at the S70R Steering Wheel Controls Switch - Right. Connect the harness connector at the and P29 Head-Up Display. Ignition ON.
  10. Verify head-up display functions properly.
    • If head-up display functions properly 

      Replace S70R Steering Wheel Controls Switch - Right.

    • If head-up display does not function properly 
  11. Replace P16 Instrument Cluster.

Left Controls Malfunction

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the S70L Steering Wheel Controls Switch - Left.
  2. Test for less than 10Ω between the ground circuit terminal 10 and ground.
    • If greater than 10Ω 
    1. Ignition OFF.
    2. Test for less than 2Ω in the ground circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, repair the open/high resistance in the ground connection.
    • If less than 10Ω 
  3. Test for 4.8-5.2V between the volt between the following signal circuits and ground
    • Voice - Terminal 6
    • Mute - Terminal 5
    • If less than 4.8V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2Ω in the signal circuit end to end.
      • If 2Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2Ω, replace the P16 Instrument Cluster.
    • If greater than 5.2V 
    1. Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster, ignition ON.
    2. Test for less than 1V between the signal circuit and ground.
      • If 1V or greater, repair the short to voltage on the circuit.
      • If less than 1V, replace the P16 Instrument Cluster.
      • If between 4.8-5.2V 
  4. Replace the S70L Steering Wheel Controls Switch - Left.
scientia non olet · About LEMON Manuals