LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2009 >> Allure CX >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Mechanical - 5.3L) >> Repair Instructions - Off Vehicle >> Crankshaft and Bearing Installation >> Installation

Crankshaft and Bearing Installation: Installation

WARNING: This page is about a different variant/trim than selected.
    Fig 1: View Of Crankshaft Bearings & Bearing Caps
    GM64293Courtesy of GENERAL MOTORS CORP.
    NOTE:
    • Crankshaft bearing clearances are critical. Excessive crankshaft bearing clearance may affect crankshaft position sensor signals and/or on-board diagnostics (OBD) II system performance.
    • Crankshaft bearing caps must be installed to the proper location and direction.
    • When installing the crankshaft bearings, align the locating tabs on the bearings with the locating notches in the engine block journal bore and the bearing cap.
    • Always install crankshaft bearings with their machined partner. Do not file bearings or mix bearing halves.
    • To prevent engine block oil leakage, install NEW M8 crankshaft bearing cap side bolts.

      The crankshaft bearing cap M8 side bolts have a pre-applied sealant patch applied to the bolt flange.

  1. Install the crankshaft bearings to the engine block and bearing caps. The thrust bearings are to be installed into center journal.
  2. Lubricate the bearing surfaces and crankshaft journals with clean engine oil.
    3. Fig 2: View Of Crankshaft & Engine Block
    GM156151Courtesy of GENERAL MOTORS CORP.
    CAUTION: To maintain proper crankshaft end play, use extreme care during crankshaft installation. Avoid scoring or damaging the thrust bearing.
  3. Install the crankshaft.
    4. Fig 3: View of Proper Bearing Cap Installation
    GM1870578Courtesy of GENERAL MOTORS CORP.
    NOTE: The bearing caps must be installed in the proper location and direction.
  4. Install the crankshaft bearing caps, with bearings, into the engine block.
    5. Fig 4: Identifying Bearing Cap Bolts & Studs
    GM1552494Courtesy of GENERAL MOTORS CORP.
  5. Install the M10 bolts (129) and M10 studs (128).
  6. Tap the bearing caps into place with a plastic-face hammer.
  7. Install the NEW M8 bearing cap side bolts (127).
    8. Fig 5: Crankshaft Main Bearing Cap Bolt Tightening Sequence
    GM63214Courtesy of GENERAL MOTORS CORP.
    CAUTION: Refer to Fastener Caution .
  8. Tighten the bearing cap M10 bolts (1-10) a first pass in sequence to 20 N.m (15 lb ft).
    9. NOTE: To properly align the crankshaft thrust bearings, the final thrust of the crankshaft MUST be in the forward direction.
  9. Using a plastic-face hammer, tap the crankshaft rearward, then forward to align the thrust bearings.
    1. Tighten the M10 bolts (1-10) a final pass in sequence 80 degrees using the J 45059  .
    2. Tighten the M10 studs (11-20) a first pass in sequence to 20 N.m (15 lb ft) .
    3. Tighten the M10 studs (11-20) a final pass in sequence 51 degrees using the J 45059:  meter .
    4. Tighten the bearing cap M8 bolts to 25 N.m (18 lb ft) .

      Tighten the bolt on one side of the bearing cap and then tighten the bolt on the opposite side of the same bearing cap.

    10. Fig 6: CKP Sensor, Bolt & O-Ring
    GM1402083Courtesy of GENERAL MOTORS CORP.
  10. Install the crankshaft position (CKP) sensor.
    1. Inspect the CKP sensor O-ring seal (750). If the O-ring seal is not cut or damaged, it may be used.
    2. Coat the O-ring seal with clean engine oil.
    3. Install the O-ring onto the sensor.
    4. Install the sensor (701). Rotate the sensor until the locating hole in the bracket aligns with the bolt hole in the block.
    5. Install the sensor bolt (702) to 25 N.m (18 lb ft) .
    11. Fig 7: Measuring Crankshaft End Play
    GM64316Courtesy of GENERAL MOTORS CORP.
  11. Measure the crankshaft end play.
    1. Thrust the crankshaft forward or rearward.
    2. Insert a feeler gage between the center crankshaft bearing and the bearing surface of the crankshaft and measure the bearing clearance.

      The proper crankshaft end play clearance is 0.04-0.2 mm (0.0015-0.0078 in).

    3. If the bearing clearance is not within specifications, inspect the thrust surfaces for nicks, gouges or raised metal. Minor imperfections may be removed with a fine stone.
scientia non olet · About LEMON Manuals