LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2009 >> Allure CX >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Engine Mechanical - 5.3L) >> Repair Instructions - Off Vehicle >> Crankshaft Rear Oil Seal Housing Installation >> Installation

Crankshaft Rear Oil Seal Housing Installation: Installation

WARNING: This page is about a different variant/trim than selected.
    Fig 1: View Of Engine Block Rear Oil Gallery Plug
    GM63228Courtesy of GENERAL MOTORS CORP.
    NOTE:
    • Do not use the crankshaft rear oil seal or the engine rear housing gasket again.
    • Do not apply any type of sealant to the rear housing gasket, unless specified.
    • The special tools in this procedure are used to properly align the engine rear housing at the oil pan surface and to center the crankshaft rear oil seal.
    • The crankshaft rear oil seal will be installed after the rear housing has been installed and aligned. Install the rear housing without the crankshaft oil seal.
      • The crankshaft rear oil seal MUST be centered in relation to the crankshaft.
      • The oil pan sealing surface at the rear housing and engine block MUST be aligned within specifications.
      • An improperly aligned rear housing may cause premature rear oil seal wear and/or engine assembly oil leaks.
  1. Inspect the rear oil gallery plug for proper installation.
    2. Fig 2: View of Rear Housing, Gasket and Seal
    GM1552544Courtesy of GENERAL MOTORS CORP.
  2. Install the rear housing gasket (519), rear housing (518), and bolts (517).
  3. Tighten the bolts finger tight. Do not overtighten.
    4. Fig 3: View Of J 41480 Installed To Engine Block
    GM64204Courtesy of GENERAL MOTORS CORP.
    CAUTION: Refer to Fastener Caution .
    NOTE: Start the J 41480:  alignment tool-to-rear housing bolts. Do not tighten the bolts at this time.
  4. Install the J 41480:  alignment and bolts and tighten the tool-to-engine block bolts to 25 N.m (18 lb ft).
    5. Fig 4: View Of J 41480 & J 41476
    GM63243Courtesy of GENERAL MOTORS CORP.
    NOTE: To properly align the rear housing, the J 41476:  tool must be installed onto the rear of the crankshaft with the tool mounting bolts parallel to the oil pan surface.
  5. Rotate the crankshaft until 2 opposing flywheel bolt holes are parallel to the oil pan surface.
    6. Fig 5: View Of J 41480 & J 41476 Installed
    GM65286Courtesy of GENERAL MOTORS CORP.
    NOTE: The tapered legs of the alignment tool must enter the rear housing oil seal bore.
  6. Install the J 41476:  tool and bolts onto the rear of the crankshaft.
    1. Tighten the tool mounting bolts until snug. Do not overtighten.
    2. Tighten the J 41480:  alignment tool-to-rear housing bolts evenly to 12 N.m (106 lb in) .
    3. Tighten the rear housing bolts to 30 N.m (22 lb ft) .
  7. Remove the tools.
    8. Fig 6: Checking Rear Cover-To-Engine Block Proper Installation Position
    GM63240Courtesy of GENERAL MOTORS CORP.
  8. Measure the rear housing-to-engine block oil pan surface for flatness.
    1. Place a straight edge onto the engine block and rear housing oil pan sealing surfaces.

      Avoid contact with the portion of the gasket that protrudes into the oil pan surface.

    2. Insert a feeler gage between the rear housing and the straight edge. The housing must be flush with the oil pan or no more than 0.5 mm (0.02 in) below flush.
  9. If the rear housing-to-engine block oil pan surface alignment is not within specifications, repeat the housing alignment procedure.
  10. If the correct rear housing-to-engine block alignment at the oil pan surface cannot be obtained, replace the rear housing.
scientia non olet · About LEMON Manuals