LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 36 (Battery, Charging System And Starting System) >> Diagnostic Information and Procedures >> Starter Solenoid Does Not Click

Starter Solenoid Does Not Click

WARNING: This page is about a different car, the 2005 Buick LaCrosse and 2005 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.
Starter Solenoid Does Not Click

Step Action Yes No
Schematic References:  Starting and Charging Schematics  
Connector End View Reference: Master Electrical Component List in Wiring Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 Turn the ignition to the START position.
Does the engine crank?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Verify that the transmission is in Park or Neutral.
  4. With a scan tool, observe the IMS parameter in the PCM/ECM data list.
Does the scan tool display Park or Neutral?		 Go to Step 4  Go to Range Selector Displays Incorrect Range (3.6L) or Range Selector Displays Incorrect Range (3.8L) in Automatic Transaxle - 4T65-E
4
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, observe the Starter Relay Command parameter in the PCM/ECM data list.
  3. Turn the ignition to the START position.
Does the scan tool display Yes?		 Go to Step 6  Go to Step 5 
5
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, observe the Starter Switch parameter in the BCM data list.
  3. Turn the ignition to the START position.
Does the scan tool display Yes?		 Go to Step 15  Go To Power Mode Mismatch in Computer/Integrating Systems
6
  1. Disconnect the Crank relay.
  2. Turn ON the ignition, with the engine OFF.
  3. Connect a test lamp between the battery positive voltage circuit of the Crank relay coil and a good ground.
Does the test lamp illuminate?		 Go to Step 7  Go to Step 16 
7
  1. Connect a test lamp between the battery positive voltage circuit of the Crank relay coil and the control circuit of the Crank relay.
  2. Turn the ignition to the START position.
Does the test lamp illuminate?		 Go to Step 8  Go to Step 12 
8
  1. Turn OFF the ignition.
  2. Connect a test lamp between the battery positive voltage circuit of the Crank relay switch and a good ground.
Does the test lamp illuminate?		 Go to Step 9  Go to Step 17 
9
IMPORTANT: The engine may crank during the following step.
  1. Turn OFF the ignition.
  2. Connect a 30-amp fused jumper between the battery positive voltage circuit of the Crank relay switch and the starter solenoid crank voltage circuit of the Crank relay.
Does the engine crank?		 Go to Step 13  Go to Step 10 
10 Does the fuse in the jumper open? Go to Step 18  Go to Step 11 
11 Test the starter solenoid crank voltage circuit of the starter solenoid for a high resistance or open. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 22  Go to Step 14 
12 Test the control circuit of the Crank relay for an open or short to battery voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 22  Go to Step 15 
13 Inspect for poor connections at the Crank relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 22  Go to Step 19 
14 Inspect for poor connections at the starter solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 22  Go to Step 20 
15 Inspect for poor connections at the harness connector of the powertrain control module (PCM)/engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 22  Go to Step 21 
16 Repair the open or high resistance in the battery positive voltage of the Crank relay coil circuit. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 22  -
17 Repair the open or high resistance in the battery positive voltage circuit of the Crank relay switch. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 22  -
18 Repair the short to ground in the crank voltage circuit of the starter solenoid. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 22  -
19 Replace the Crank relay.
Did you complete the replacement?		 Go to Step 22  -
20 Replace the starter motor. Refer to Starter Motor Replacement (LY7)  or Starter Motor Replacement (L26) .
Did you complete the replacement?		 Go to Step 22  -
21
IMPORTANT: Perform the set up procedures for the PCM/ECM.
Replace the PCM/ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.Did you complete the replacement?		 Go to Step 22  -
22 Operate the system in order to verify the repair.
Did you correct the condition?		 System OK Go to Step 2 
scientia non olet · About LEMON Manuals