LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 237 (Engine Mechanical - 3.9L) >> Repair Instructions >> Off-Vehicle Repair Instructions >> Timing Chain and Sprockets Installation >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Crankshaft Sprocket
    GM760405Courtesy of GENERAL MOTORS CORP.
  1. Install the crankshaft sprocket.
  2. Apply prelube GM P/N 12345501 (Canadian P/N 992704) or the equivalent to the crankshaft sprocket thrust surface.
    3. Fig 2: View Of Timing Chain Tensioner & Bolts
    GM1557846Courtesy of GENERAL MOTORS CORP.
  3. Install the timing chain tensioner.
    4. IMPORTANT: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    NOTE: Refer to FASTENER NOTICE in Cautions and Notices.
  4. Install the timing chain tensioner bolts.

    Tighten:  Tighten the timing chain tensioner bolts to 21 N.m (15 lb ft).

    5. Fig 3: Collapsing Tensioner
    GM1557847Courtesy of GENERAL MOTORS CORP.
  5. Using the EN-47719  , fully collapse the tensioner and place the tensioner retaining pin into the retaining hole (1). See Special Tools .
    6. Fig 4: Identifying Timing Marks & Tensioner
    GM1557849Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Always install a NEW camshaft position actuator filter anytime the camshaft position actuator is removed or installed. Refer to Camshaft and Bearings Cleaning and Inspection  for filter changing instructions.
  6. Align the crankshaft timing mark (1) to the timing mark on the bottom of the timing chain tensioner (2).
  7. Hold the camshaft sprocket with the timing chain hanging down and install the timing chain to the crankshaft gear.
    8. Fig 5: Identifying Timing Chain & Sprockets
    GM1557851Courtesy of GENERAL MOTORS CORP.
  8. Align the timing mark on the camshaft gear (4) with the timing mark on top of the timing chain tensioner (3).
    9. Fig 6: Identifying Camshaft Position Sensor Actuator & Bolts
    GM1706684Courtesy of GENERAL MOTORS CORP.
  9. Align the dowel in the camshaft position actuator with the dowel hole in the camshaft.
    10. NOTE: Use only a Torx Plus® Bit when removing or installing the camshaft position actuator fasteners (1). The Torx Plus® design differs from typical Torx® fastener. Use of a standard Torx® bit on Torx Plus® fasteners may result in a rounded out fastener head or incorrect faster torque.
    IMPORTANT: DO NOT use any type of threadlocking compound on the camshaft position actuator mounting bolts. Usage of a threadlocking compound on the threads could lead to contamination of the camshaft position actuator, possibly resulting in potential damage to the actuator.
  10. Draw the camshaft sprocket onto the camshaft using the mounting bolts.

    Tighten:  Tighten the bolts to 16 N.m (12 lb ft).

  11. Remove the tensioner retaining pin.
  12. Coat the crankshaft and camshaft sprocket with engine oil.
scientia non olet · About LEMON Manuals