LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 23 (Automatic Transaxle (DTC P0218 To DTC P0742)) >> Diagnosis >> DTC P0712 (3.6L) >> Test Description

Test Description

WARNING: This page is about a different car, the 2005 Buick LaCrosse and 2005 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refers to the step numbers on the diagnostic table.

  1. 2:  A value below 0.2 volts indicates the fault is present. A value above 0.2 volts indicates the fault is intermittent.
  2. 3:  A value greater than 4.9 volts indicates the fault is in the transmission side.
  3. 5:  For resistance at other temperatures, refer to Transmission Fluid Temperature (TFT) Sensor Specifications.
DTC P0712 (3.6L)

Step Action Value(s) Yes No
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Install a scan tool.
  2. Turn ON the ignition with the engine OFF.
    3. IMPORTANT: Before clearing the DTCs, use the scan tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the TCM.
  3. Record the Failure Records.
  4. Clear the DTCs.
  5. With the scan tool, observe the TFT Sensor parameter.
Does the scan tool indicate that the TFT sensor voltage is less than specified?		 0.2 V Go to Step 3  Go to Intermittent Conditions in Engine Controls - 3.6L
3 
  1. Turn OFF the ignition.
  2. Disconnect the transmission 20-way connector. Additional DTCs will set.
  3. Turn ON the ignition with the engine OFF.
  4. Observe the TFT Sensor parameter.
Does the scan tool indicate that the TFT sensor voltage is greater than specified?		 4.9 V Go to Step 5  Go to Step 4 
4 Test the signal circuit of the TFT sensor for a short to ground between the TCM and the AT inline 20-way connector.
Refer to Testing for Short to Ground andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 11  Go to Step 10 
5 
  1. Connect the J 44152  jumper harness to the transmission side of the 20-way connector. See Special Tools .
  2. Using the J 35616  GM terminal test kit, connect the DMM to the TFT sensor circuit of the J 44152  . See Special Tools .

    Refer to Automatic Transmission Inline 20-Way Connector End View (3.6L) or Automatic Transmission Inline 20-Way Connector End View (3.8L) .

  3. Measure the resistance.
Does the resistance measure within the range specified for the given transmission temperatures?		 3,164-3,867 Ω @ 20°C (68°F)
225-285 Ω @ 88°C (190°F)		 Go to Step 6  Go to Step 7 
6 Test the signal circuit of the TFT sensor for a short to ground between the AT inline 20-way connector and the TFT sensor.
Refer to Testing for Short to Ground in Wiring Systems.
Did you find the condition?		 - Go to Step 9  Go to Intermittent Conditions in Engine Controls - 3.6L
7
  1. Disconnect the TFT sensor from the transmission internal wiring harness.
  2. Test the signal circuit and the low reference circuit for a short together between the A/T inline 20-way connector and the TFT sensor.
Refer to Testing for Continuity in Wiring Systems.Did you find the condition?		 - Go to Step 9  Go to Step 8 
8 Replace the TFT sensor.
Refer to Fluid Temperature Sensor Replacement .
Did you complete the replacement?		 - Go to Step 11  -
9 Replace the automatic transmission wiring harness.
Refer to Wiring Harness Replacement .
Did you complete the replacement?		 - Go to Step 11  -
10 Replace the TCM.
Refer to Control Module References in Computer/Integrating Systems for replacement, set-up or programming.
Did you complete the replacement?		 - Go to Step 11  -
11 Perform the following procedure In order to verify the repair:
  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
    • Turn ON the ignition with the engine OFF.
    • Verify that the TFT sensor is 144°C (291°F) or less for 2 seconds.
  4. Select specific DTC.
  5. Enter DTC P0712.

Has the test run and passed?		 - Go to Step 12  Go to Step 2 
12 With a scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information System OK
scientia non olet · About LEMON Manuals