LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 222 (Heating, Ventilation And Air Conditioning) >> Repair Instructions >> Flushing >> Flushing Procedure

Flushing Procedure

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.
    IMPORTANT: Warmer engine or ambient temperature decreases the refrigerant recovery time during the A/C flush procedure.
  1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
  2. Remove the thermal expansion valve (TXV). Refer to Thermal Expansion Valve Replacement .
  3. Install the J 45268-103 in place of the TXV.
  4. Remove the auxiliary TXV. Refer to Thermal Expansion Valve Replacement - Auxiliary .
  5. Install J 45268-107 in place of the auxiliary TXV.
  6. Remove the A/C compressor. Refer to Compressor Replacement .
  7. Install J 45268-5 to the discharge hose.
  8. Install J 45268-4 to the suction hose.
    9. Fig 1: View Of A/C Filter And Check Valve
    GM787687Courtesy of GENERAL MOTORS CORP.
  9. Forward flow refrigerant flushing is recommended for contaminated refrigerant or PAG oil.

    Perform the following procedure:

      IMPORTANT: The filter inside J 45268-1 is serviceable. Remove and discard the check valve from the filter.
    1. Service the filter with ACDelco P/N GF 470 before each flush.
    2. Connect J 45268-1 to the suction port of J 45268-4.
    3. Connect the blue hose from J 43600  to J 45268-1 flush filter adapter.
    4. Connect the red hose from J 43600  to J 45268-5 flush adapter.
  10. Reverse flow refrigerant flushing is recommended for desiccant bag failure. Replace the receiver dehydrator when the A/C flush is complete and perform the following procedure:
      IMPORTANT: The filter inside J 45268-1 is serviceable.
    1. Service the filter with ACDelco P/N GF 470 before each flush.
    2. Connect J 45268-1 to the discharge port of J 45268-5.
    3. Connect the blue hose from J 43600  to J 45268-1 flush filter adapter.
    4. Connect the red hose from J 43600  to the suction port of J 45268-4 flush adapter.
    11. IMPORTANT: Close the valve on the external refrigerant tank before starting the flush process.
  11. Flush the front A/C system. Follow the instructions supplied with the J 43600  .
    12. IMPORTANT: Flush the front A/C system before flushing the auxiliary A/C system.
  12. If the vehicle is equipped with rear A/C, flush the auxiliary A/C system separately.
    1. Remove J 45268-107 from the auxiliary evaporator core.
    2. Remove J 45268-103.
    3. Install J 45268-103 to the auxiliary evaporator core.
    4. Install J 45268-107.
  13. Flush the auxiliary A/C system. Follow the instructions supplied withJ 43600  .
  14. Remove J 45268-5 from the discharge hose.
  15. Remove J 45268-4 from the suction hose.
    16. IMPORTANT: Flushing will remove all the PAG oil from the A/C system.
    The A/C system must be replenished with the correct amount of PAG oil.
  16. If the removed A/C compressor is being reinstalled, perform the following procedure:
    1. Drain the PAG oil from the A/C compressor.

      Rotate the compressor input shaft to assist in draining the PAG oil from the compressor.

    2. Add the total system capacity of PAG oil to the A/C compressor. Refer to Refrigerant System Capacities  .
  17. If you will replace the A/C compressor after flushing the system, perform the following procedure:
    1. A new service compressor is shipped with PAG oil. Refer to the Refrigerant System Capacities  .
    2. If the service compressor is shipped with PAG oil, DO NOT drain the new PAG oil from the compressor.
    3. Deduct the amount of PAG oil shipped with the service compressor from the amount of PAG oil listed in the capacities table. Refer to Refrigerant System Capacities  .

      Add the calculated amount to the compressor, as needed.

    18. IMPORTANT: Flushing will remove the fluorescent leak detection dye from the A/C system.
  18. Add one bottle of J 41447  directly to the A/C compressor.
  19. Install the A/C compressor. Refer to Compressor Replacement .
  20. Remove J 45268-103.
  21. Inspect the TXV for debris. Clean or replace as needed.
  22. Install the auxiliary TXV. Refer to Thermal Expansion Valve Replacement - Auxiliary .
  23. Remove J 45268-107.
  24. Inspect the TXV for debris. Clean or replace as needed.
  25. Install the TXV. Refer to Thermal Expansion Valve Replacement .
  26. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
  27. Leak test the fittings using J 42220  .
scientia non olet · About LEMON Manuals