LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 197 (Engine Cooling System) >> Diagnostic Information and Procedures >> DTC P0480 or P0481 >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the cool fan 1 relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 3:  Listen for an audible click when the cool fan 2 and cool fan 3 relays operate. Command both the ON and OFF states. Repeat the commands as necessary.
  3. 4:  This step tests for voltage at the coil side of the cool fan 1 relay. The COOL FAN 1 fuse supplies battery positive voltage to the coil side of the cool fan 1 relay.
DTC P0480 or P0481

Step Action Yes No
Schematic Reference: Engine Cooling Schematics 
Connector End View Reference: Cooling System Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the Fans Low Speed ON and OFF.
Does the cool fan 1 relay turn ON and OFF with each command?		 Go to Step 3  Go to Step 4 
3  With a scan tool, command the Fans High Speed ON and OFF.
Do the cool fan 3 and the cool fan 2 relays turn ON and OFF with each command?		 Go to Diagnostic Aids Go to Step 6 
4 
  1. Turn OFF the ignition.
  2. Disconnect the cool fan 1 relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the battery positive voltage circuit of the cool fan 1 relay with a test lamp that is connected to a good ground.
Does the test lamp illuminate?		 Go to Step 5  Go to Step 16 
5
  1. Connect a test lamp between the control circuit of the cool fan 1 relay and the battery positive voltage circuit of the cool fan 1 relay.
  2. With a scan tool, command the Fans Low Speed ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 12  Go to Step 9 
6
  1. Turn OFF the ignition.
  2. Disconnect the cool fan 2 relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the battery positive voltage circuit of the cool fan 2 relay with a test lamp that is connected to a good ground.
Does the test lamp illuminate?		 Go to Step 7  Go to Step 16 
7
  1. Connect a test lamp between the control circuit of the cool fan 3 relay and the battery positive voltage circuit of the cool fan 3 relay.
  2. With a scan tool, command the Fans High Speed ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 14  Go to Step 8 
8
  1. Turn OFF the ignition.
  2. Disconnect the cooling fan 3 relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the control circuit of the cool fan 3 relay and the battery positive voltage circuit of the cool fan 3 relay.
  5. With a scan tool, command the Fans High Speed ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 13  Go to Step 9 
9 Does the test lamp remain illuminated with each command? Go to Step 11  Go to Step 10 
10 Test the control circuit of the appropriate relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 21  Go to Step 15 
11 Test the control circuit of the appropriate relay for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 21  Go to Step 15 
12 Inspect for poor connections at the cool fan 1 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 21  Go to Step 17 
13 Inspect for poor connections at the cool fan 3 relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 21  Go to Step 18 
14 Inspect for poor connections at the cool fan relay 2. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 21  Go to Step 19 
15 Inspect for poor connections at the harness connector of the powertrain control module (PCM) or engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 Go to Step 21  Go to Step 20 
16 Repair the battery positive voltage circuit. Refer to Wiring Repairs .
Did you complete the repair?		 Go to Step 21  -
17 Replace the cool fan 1 relay.
Did you complete the replacement?		 Go to Step 21  -
18 Replace the cool fan 3 relay.
Did you complete the replacement?		 Go to Step 21  -
19 Replace the cool fan 2 relay.
Did you complete the replacement?		 Go to Step 21  -
20 Replace the PCM/ECM. Refer to Control Module References for replacement, setup and programming.
Did you complete the replacement?		 Go to Step 21  -
21
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals