LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 181 (Supplemental Inflatable Restraint System) >> Diagnostic Information and Procedures >> DTC B0092 >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step checks the PPS for any current or history DTCs.
  2. 5:  Test the occupant sensor serial data circuit for an open or high resistance.
  3. 6:  Test the PPS ignition 1 voltage circuit for a short to ground, a high resistance or an open.
  4. 7:  Test the PPS ground circuit for an open or high resistance.
  5. 8:  Test the PPS ground circuit for a short to voltage.
DTC B0092

Step Action Yes No
Schematic Reference: SIR Schematics (AK5 or AJ7)  or SIR Schematics (AW9) 
Connector End View Reference: SIR Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: If the passenger presence system (PPS) has any current or history DTCs stored, you must address the PPS DTCs before continuing with this diagnostic table.
  3. Use the scan tool to request the PPS DTCs. Refer to Passenger Presence System Flash Code Procedures .
Does the PPS flash any current or history DTCs?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information Go to Step 3 
3
  1. Turn OFF the ignition.
  2. Disconnect the PPS module connector. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
  3. Inspect the PPS module connector for corrosion or damage. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 4 
4
  1. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
  2. Inspect the SDM connector for damage or corrosion. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 5 
5  Test the occupant sensor serial data circuit for an open or high resistance between the PPS and SDM connector. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 6 
6  Test the PPS ignition 1 voltage circuit for one of the following:
  • An open
  • High resistance
  • Short to ground

Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 7 
7  Test the PPS ground circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 8 
8 
  1. Turn ON the ignition, with the engine OFF.
  2. Test the PPS ground circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 10  Go to Step 9 
9
  1. Turn OFF the ignition.
    2. IMPORTANT: The PPS is a calibrated system. The PPS must be rezero after replacement.
  2. Replace the PPS. The PPS is only serviceable as a PPS and seat bottom foam assembly. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?		 Go to Step 10  -
10
  1. Reconnect all SIR and PPS system components.
  2. Verify that all components, connectors and connector position assurances (CPAs) are properly mounted.
  3. Use the scan tool in order to clear the SIR and PPS DTCs.
  4. Rezero the PPS. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
  5. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals