LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 181 (Supplemental Inflatable Restraint System) >> Diagnostic Information and Procedures >> DTC B0057, B0058 or B0059 >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 4:  This step tests to see if the malfunction is caused by the seat belt pretensioner RF.
  2. 6:  This step tests to see what DTCs are present. If DTC B0057 is present, test the seat belt pretensioner RF for a short between high and low circuits. If DTC B0058 is present, test the seat belt pretensioner RF high and low circuits for an open and for high resistance. If DTC B0059 is present, test the seat belt pretensioner RF high and low circuits for a short to ground and for a short to voltage.
DTC B0057, B0058 or B0059

Step Action Yes No
Schematic Reference: SIR Schematics (AK5 or AJ7)  or SIR Schematics (AW9) 
Connector End View Reference: SIR Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Turn OFF the ignition.
  2. Disconnect the seat belt retractor pretensioner RF inline connector. Refer to Seat Belt Retractor Pretensioner Replacement - Right Front .
  3. Inspect the component and harness sides of the inline connector for the seat belt pretensioner for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections andConnector Repairs in Wiring Systems.
Does the connector exhibit any signs of damage or corrosion?		 Go to Step 3  Go to Step 4 
3
  1. If the connector for the seat belt pretensioner RF is damaged, the seat belt pretensioner must be replaced. Refer to Seat Belt Retractor Pretensioner Replacement - Right Front .
  2. If the wiring harness side of the seat belt pretensioner connector is damaged, replace the harness side of the connector. Refer to Connector Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 9  -
4 
    IMPORTANT: If the scan tool displays multiple codes, diagnose the open code first.
  1. Using the J 38715-30A, connect the J 38715-A  SIR Driver/Passenger Load Tool or SA9409Z-A to the harness side of the seat belt pretensioner RF connector. See Special Tools . Use the PASSENGER INFLATOR connector.
  2. Turn ON the ignition, with the engine OFF.
  3. With the scan tool, request the SIR DTC display.
Does the scan tool indicate that DTC B0057, B0058 or B0059 are current?		 Go to Step 5  Go to Step 7 
5
  1. Turn OFF the ignition.
  2. Disconnect and remove the J 38715-A  or SA9409Z-A and adapter. See Special Tools .
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
  4. Inspect the SDM connector for damage or corrosion that may cause a malfunction in the seat belt pretensioner RF high and/or low circuits. Refer to Testing for Intermittent Conditions and Poor Connections andConnector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 6 
6 
  1. If DTC B0057 is present, test the seat belt pretensioner RF for a short between the high and low circuits.
  2. If DTC B0058 is present, test the seat belt pretensioner RF high and low circuits for an open and for high resistance.
  3. If DTC B0059 is present, test the seat belt pretensioner RF high and low circuits for a short to ground and for a short to voltage.
  4. All the above conditions refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 9  Go to Step 8 
7
  1. Turn OFF the ignition.
  2. Replace the seat belt pretensioner RF. Refer to Seat Belt Retractor Pretensioner Replacement - Right Front .
Did you complete the replacement?		 Go to Step 9  -
8
  1. Turn OFF the ignition.
  2. Replace the SDM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming.
Did you complete the replacement?		 Go to Step 9  -
9
  1. Connect all SIR components.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals