LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 169 (Vehicle DTC Information) >> Diagnostic Information and Procedures >> Diagnostic System Check - Vehicle >> Test Description

Test Description

WARNING: This page is about a different car, the 2006 Pontiac Montana SV6, 2006 Chevrolet Uplander, and 2006 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 1:  This step ensures that the battery and the vehicle primary power and ground systems are functioning correctly.
  2. 3:  Lack of communication may be due to a particular malfunction of a serial data circuit. The information in Scan Tool does not Communicate with Class 2 Device will provide a list of modules and the associated data network no communication diagnostic link.
  3. 4:  A module that is operating in the incorrect power mode based on key position may cause other vehicle symptoms and/or DTCs to set. The information in Power Mode Mismatch will correct the condition before checking for module DTCs or symptoms.
  4. 8:  This step ensures that all data link communication DTCs are diagnosed before system level DTCs.
  5. 9:  This step ensures that all electronic control unit (ECU) internal DTCs are diagnosed before other system level DTCs.
  6. 10:  This step ensures that all device voltage DTCs are diagnosed before other system level DTCs.
Diagnostic System Check - Vehicle

Step Action Yes No
1  Perform the following preliminary inspections:
  • Ensure that the battery is fully charged. Refer to Battery Inspection/Test .
  • Ensure that the battery cables are clean and tight.
  • Inspect for any open fuses.
  • Inspect the easily accessible systems or the visible system components for obvious damage or conditions that could cause the symptom.
  • Ensure that the grounds are clean, tight and in the correct location.
  • Inspect for aftermarket devices that could affect the operation of the system. Refer to Checking Aftermarket Accessories .
  • Search for applicable service bulletins.

Did you find and correct the condition?		 System OK Go to Step 2 
2 Install a scan tool.
Does the scan tool power up?		 Go to Step 3  Go to Scan Tool Does Not Power Up
3 
  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to establish communication with all of the control modules on the vehicle. Refer to Scan Tool Does Not Communicate with Class 2 Device for the modules you should expect to observe.
Does the scan tool communicate with all of the expected vehicle control modules?		 Go to Step 4  Go to Scan Tool Does Not Communicate with Class 2 Device
4 
IMPORTANT:
  • To ensure that retained accessory power (RAP) mode is inactive, if equipped, open the drivers door during the following step.
  • The engine may start during the following step. Turn OFF the engine as soon as you have observed the crank power mode.
  1. Access the Power Mode parameter on the scan tool.
  2. Rotate the ignition switch, operate the ignition mode switch, through all positions while observing the Power Mode parameter. Refer to Body Control System Description and Operation for a list of the power mode states that correspond with each switch position.
Does the Power Mode parameter reading on the scan tool match the ignition switch position for all switch positions?		 Go to Step 5  Go to Power Mode Mismatch
5 Attempt to start the engine.
Does the engine crank?		 Go to Step 6  Go to Symptoms - Engine Electrical
6 Attempt to start the engine.
Does the engine start and idle?		 Go to Step 7  Go to Engine Cranks but Does Not Run for the 3.5L (LX9) engine
or
Engine Cranks but Does Not Run for the 3.9L engine
7
IMPORTANT: Do not clear any DTCs unless instructed by a diagnostic procedure.
Use the appropriate scan tool selections to obtain DTCs for each of the control modules.Does the scan tool display any DTCs?		 Go to Step 8  Go to Step 12 
8  Does the scan tool display any DTCs that begin with a "U"? Go to Diagnostic Trouble Code (DTC) List - Vehicle  Go to Step 9 
9 
IMPORTANT: If any of these DTCs are displayed, diagnose them before diagnosing any other DTCs or symptoms.
Does the scan tool display DTC B1000, B1001, B1004, B1007, B1009, B1013, C0550, P0601, P0602, P0603, P0604, P0606, P062F, P2107, P2108, P2610?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle  Go to Step 10 
10 
IMPORTANT: If any of these DTCs are displayed, diagnose them before diagnosing any other DTCs or symptoms.
Does the scan tool display DTC B1327, B1328, B1370, B1390, B1420, C0899, C0900, P0562, P0563?		 Go to Diagnostic Trouble Code (DTC) List - Vehicle  Go to Step 11 
11
IMPORTANT: If any of the remaining DTCs are powertrain DTCs, select Capture Info in order to store the powertrain DTC information with a scan tool.
If multiple DTCs are stored, diagnose the DTCs in the following order:
  1. Component level DTCs, such as sensor DTCs, solenoid DTCs and relay DTCs.
  2. System level DTCs, such as misfire DTCs, evaporative emission (EVAP) system DTCs and fuel trim DTCs.
Diagnose the remaining DTCs.		 Go to Diagnostic Trouble Code (DTC) List - Vehicle  -
12 Is the customers concern with inspection/maintenance (I/M) testing? Go to Inspection/Maintenance (I/M) System Check for the 3.5L (LX9) engine
or
Inspection/Maintenance (I/M) System Check for the 3.9L engine		 Go to Symptoms - Vehicle 
scientia non olet · About LEMON Manuals