LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Lucerne CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 120 (Engine Mechanical - 3.8L) >> Repair Instructions >> On-Vehicle Repair Instructions >> Replacing Cylinder Head - Right >> Installation

Replacing Cylinder Head - Right: Installation

WARNING: This page is about a different car, the 2006 Buick LaCrosse and 2006 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the valves, the seals, the springs and the caps to the cylinder head. Refer to Cylinder Head Assemble .
    2. NOTE: Head gaskets are not interchangeable. The head gasket must be installed with the arrow pointing to the front of the engine. Installing the head gasket in any other direction will cause gasket failure and possible engine failure.
    Fig 1: Right Cylinder Head Gasket
    GM190560Courtesy of GENERAL MOTORS CORP.
  2. Position the head gasket with the arrow pointing to the front of the engine.
    3. Fig 2: Right Cylinder Head & Bolts
    GM153598Courtesy of GENERAL MOTORS CORP.
  3. Install the cylinder head.
    4. NOTE: This bolt is designed to permanently stretch when tightened. The correct part number fastener must be used to replace this type of fastener. Do not use a bolt that is stronger in this application. If the correct bolt is not used, the parts will not be tightened correctly. The system or the components may be damaged.
    NOTE: This engine uses special torque to yield head bolts. This design bolt requires a special tightening procedure. Failure to follow the given procedure will cause head gasket failure and possible engine damage.
    Fig 3: Identifying Cylinder Head Bolt Tightening Sequence
    GM38826Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice in General Information.
  4. Install the new cylinder head bolts (1-8).

    Tighten: 

    1. Tighten the cylinder head bolts in the following sequence (1-8) to 50 N.m (37 Ft. Lbs.).
    2. Use the J 45059  to rotate the cylinder head bolts in the following sequence (1-8) an additional 120 degrees.

  5. Install the right push rods and rocker arms. Refer to Replacing Valve Rocker Arm and Push Rod .
  6. Install the right valve rocker arm cover. Refer to Replacing Valve Rocker Arm Cover - Right .
  7. Install the right exhaust manifold. Refer to Replacing Exhaust Manifold - Right in Engine Exhaust.
  8. Install the EGR valve inlet adapter pipe to the right cylinder head. Refer to Replacing Exhaust Gas Recirculation (EGR) Inlet Pipe in Engine Controls - 3.8L.
  9. Install the lower intake manifold. Refer to Replacing Intake Manifold - Lower .
  10. Install the right spark plugs to the right cylinder head. Refer to Spark Plug Replacement in Engine Controls - 3.8L.
  11. Carefully release the J 41131  and return the engine to the original position. See Special Tools .
    12. Fig 4: View Of Power Steering Pump And Mounting Bolts
    GM282122Courtesy of GENERAL MOTORS CORP.
  12. Install the power steering pump.
  13. Install the power steering pump bolts.

    Tighten:  Tighten the bolts to 34 N.m (25 Ft. Lbs.).

  14. Install the drive belt tensioner. Refer to Replacing Drive Belt Tensioner .
  15. Install the left and the right engine mount struts. Refer to Replacing Engine Mount Strut - Right  and Replacing Engine Mount Strut - Left .
  16. Raise the vehicle.
    17. Fig 5: EGR Valve Adapter Bolt & Right Exhaust Manifold
    GM911025Courtesy of GENERAL MOTORS CORP.
  17. Install the exhaust gas recirculation (EGR) valve adapter bolt (1) to the right exhaust manifold.

    Tighten:  Tighten the bolt to 29 N.m (21 Ft. Lbs.).

    18. Fig 6: Right Exhaust Manifold Heat Shield & Bolts
    GM911016Courtesy of GENERAL MOTORS CORP.
  18. Install the right exhaust manifold heat shield (1).
  19. Install the right exhaust manifold heat shield bolts (2).

    Tighten:  Tighten the bolts to 10 N.m (89 lb in).

  20. Install the catalytic converter to the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust.
  21. Lower the vehicle.
    22. Fig 7: View Of HO2S Electrical Connector & Right Exhaust Manifold
    GM911055Courtesy of GENERAL MOTORS CORP.
  22. Install the HO2S to the right exhaust manifold.

    Tighten:  Tighten the HO2S to 42 N.m (31 Ft. Lbs.).

  23. Connect the HO2S electrical connector.
  24. Install the fuel injector sight shield. Refer to Replacing Fuel Injector Sight Shield .
  25. Fill the crankcase with engine oil. Refer to Replacing Engine Oil and Oil Filter .
  26. Fill the cooling system. Refer to Draining and Filling Cooling System (L26 Static Fill) or Draining and Filling Cooling System (L26, LY7, GE 47716 Fill) in Engine Cooling.
  27. Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (L26) in Engine Electrical.
  28. Inspect for leaks.
scientia non olet · About LEMON Manuals