LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Allure CX >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 14 (Engine Mechanical - 3.6L - 5 Of 5) >> Off-Vehicle Repair Instructions (4 Of 4) >> Engine Wiring Harness Assembly Installation >> Right Side Harness Connections

Right Side Harness Connections

WARNING: This page is about a different variant/trim than selected.
    Fig 1: Identifying Engine Wiring Harness To Top Of Right Camshaft Cover
    GM1414408Courtesy of GENERAL MOTORS CORP.
  1. Connect the engine wiring harness to the top of the right camshaft cover.
    2. Fig 2: Locating Engine Wiring Harness To Front Of Right Camshaft Cover
    GM1414391Courtesy of GENERAL MOTORS CORP.
  2. Connect the engine wiring harness to the front of the right camshaft cover.
    3. Fig 3: View Of Engine Wiring Harness To Right Ignition Coils
    GM1414410Courtesy of GENERAL MOTORS CORP.
  3. Connect the engine wiring harness to the right ignition coils.
    4. Fig 4: Engine Wiring Harness From The EVAP Solenoid
    GM1414409Courtesy of GENERAL MOTORS CORP.
  4. Connect the engine wiring harness to the evaporative (EVAP) solenoid.
    5. Fig 5: Locating Engine Wiring Harness To Right Camshaft Position Sensors
    GM1414405Courtesy of GENERAL MOTORS CORP.
  5. Connect the engine wiring harness to the right camshaft position sensors.
    6. Fig 6: Identifying Engine Wiring Harness From Right Camshaft Position Actuator Valves
    GM1414406Courtesy of GENERAL MOTORS CORP.
  6. Connect the engine wiring harness to the right camshaft position actuator valves.
    7. Fig 7: Engine Wiring Harness Bracket Bolt (Lower Right Side Of Engine)
    GM1414416Courtesy of GENERAL MOTORS CORP.
  7. Install the engine wiring harness bracket to the lower right side of the engine.
  8. Install the engine wiring harness bracket bolt to the lower right side of the engine.

    Tighten:  Tighten the engine wiring harness bracket bolt to 10 N.m (89 lb in).

    9. Fig 8: Identifying Engine Wiring Harness To Right Knock Sensor
    GM1414418Courtesy of GENERAL MOTORS CORP.
  9. Connect the engine wiring harness to the right knock sensor.
    10. Fig 9: Locating Engine Wiring Harness From Crankshaft Position Sensor
    GM1414421Courtesy of GENERAL MOTORS CORP.
  10. Connect the engine wiring harness to the crankshaft position sensor.
    11. Fig 10: View Of Right Exhaust Manifold Lower Heat Shield Bolts
    GM1414383Courtesy of GENERAL MOTORS CORP.
  11. Install the right exhaust manifold lower heat shield.
  12. Install the right exhaust manifold lower heat shield bolts.

    Tighten: 

    • Tighten the larger M10 right exhaust manifold lower heat shield bolt to 50 N.m (37 lb ft).
    • Tighten the smaller M6 right exhaust manifold lower heat shield bolt to 10 N.m (89 lb in).

    13. Fig 11: Engine Wiring Harness Ground Bolt (Side Of Right Front Cylinder Head)
    GM1414407Courtesy of GENERAL MOTORS CORP.
  13. Install the engine wiring harness ground to the side of the right cylinder head at the front.
  14. Install the engine wiring harness ground bolt to the side of the right cylinder head at the front.

    Tighten:  Tighten the engine wiring harness ground bolt to 10 N.m (89 lb in).

    15. Fig 12: Engine Wiring Harness Ground Bolt (Side Of Right Rear Cylinder Head)
    GM1414415Courtesy of GENERAL MOTORS CORP.
  15. Install the engine wiring harness ground to the side of the right cylinder head at the rear.
  16. Install the engine wiring harness ground bolt to the side of the right cylinder head at the rear.

    Tighten:  Tighten the engine wiring harness ground bolt to 10 N.m (89 lb in).

scientia non olet · About LEMON Manuals