LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2007 >> Allure CX >> Repair and Diagnosis >> External Pages >> Different car >> Section 33 (Automatic Transaxle - 4T65-E - Removal & Installation, Service, Overhaul, Troubleshooting & Diagnosis) >> Repair Instructions - Off Vehicle >> Control Valve Body Assemble (Without Touch Activated Power)

Control Valve Body Assemble (Without Touch Activated Power)

WARNING: This page is about a different car, the 2008 Buick LaCrosse and 2008 Buick Allure. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of 2-3 Accumulator Valve & 3-4 Accumulator Valve Components
    GM49390Courtesy of GENERAL MOTORS CORP.
  1. Install the 2-3 accumulator valve (344), the 2-3 accumulator valve spring (346) and the 2-3 accumulator valve bore plug (343) into the 2-3 accumulator valve bushing (345).
  2. Install the 2-3 accumulator valve bore plug retainer (342) in the 2-3 accumulator valve bushing (345), into the slot indicated.
  3. Install the 3-4 accumulator valve spring (340), the 3-4 accumulator valve (341) and the 2-3 accumulator valve bushing (345) into the control valve body (301).
  4. Hold the 2-3 accumulator valve bushing assembly (345) in the control valve body (301). Install the 2-3 accumulator valve bushing assembly retainer (385) into the slot indicated.
    5. Fig 2: Locating 1-2 Accumulator Valve & 1-2 Accumulator Valve Spring
    GM49388Courtesy of GENERAL MOTORS CORP.
  5. Install the 1-2 accumulator valve spring (351), the 1-2 accumulator valve (350) and the 1-2 accumulator valve bore plug (339) into the control valve body (301).
  6. Hold the 1-2 accumulator valve bore plug (339) in the control valve body (301). Install the 1-2 accumulator valve retainer (314A) into the control valve body (301).
    7. Fig 3: Identifying 3-2 Manual Downshift Valve & 2-3 Shift Valve
    GM49387Courtesy of GENERAL MOTORS CORP.
  7. Install the 2-3 shift valve (357), the 3-2 manual downshift valve (356), the 3-2 manual downshift valve spring (355) and the 3-2 manual downshift valve bore plug (354) into the control valve body (301).
  8. Hold the 3-2 manual downshift valve bore plug (354) in the control valve body (301). Install the 3-2 manual downshift valve retainer (353) into the control valve body (301).
    9. Fig 4: View Of 3-4 Shift Valve & 4-3 Manual Downshift Valve Components
    GM49386Courtesy of GENERAL MOTORS CORP.
  9. Install the 3-4 shift valve (362), the 4-3 manual downshift valve spring (361), the 4-3 manual downshift valve (360) and the 4-3 manual downshift valve bore plug (359) into the control valve body (301).
  10. Hold the 4-3 manual downshift valve bore plug (359) in the control valve body (301). Install the 4-3 manual downshift valve retainer (314B) into the control valve body (301).
    11. Fig 5: View Of 2-3 Shift Solenoid & O-Ring
    GM49385Courtesy of GENERAL MOTORS CORP.
  11. Install a new O-ring seal (316) onto the 2-3 shift solenoid (SS) valve (315B), if it was removed.
  12. Install the 2-3 SS valve (315B) into the control valve body (301).
  13. Install the 2-3 shift solenoid valve retainer (314C) into the control valve body (301).
    14. Fig 6: Identifying TCC Regulator Apply Valve
    GM815425Courtesy of GENERAL MOTORS CORP.
  14. Install the TCC regulator apply valve bore plug O-ring seal (328) onto the TCC regulator apply valve bore plug (329).
  15. Install the TCC regulator apply valve spring (326), the TCC regulator apply valve (327) and the TCC regulator apply valve bore plug (329) into the control valve body (301).
  16. Hold the TCC regulator apply valve bore plug (329) in the control valve body (301). Install the TCC regulator apply valve bore plug retainer (314G) into the control valve body (301).
    17. Fig 7: View Of TCC PWM Solenoid
    GM49380Courtesy of GENERAL MOTORS CORP.
  17. Install new O-ring seals (305, 306) onto the TCC PWM solenoid valve (334) if they had been removed.
  18. Install the TCC control valve spring (336), the TCC control valve (335) and the TCC PWM solenoid valve (334) into the control valve body (301).
  19. Hold the TCC PWM solenoid valve (334) in the control valve body (301). Install the TCC PWM solenoid valve retainer (314F) into the control valve body (301).
    20. Fig 8: Locating Line Pressure Relief Valve Assembly
    GM49379Courtesy of GENERAL MOTORS CORP.
  20. Install the line pressure relief valve (324) and the line pressure relief valve spring (323) into the control valve body (301).
  21. Compress the line pressure relief valve spring (323) into the control valve body (301). Install the line pressure relief valve spring retainer (325) into the control valve body (301).
    22. Fig 9: View Of PC Solenoid Valve & Torque Signal Regulator Valve
    GM840865Courtesy of GENERAL MOTORS CORP.
  22. Install new O-ring seals (307, 316) onto the pressure control (PC) solenoid valve (322), if they had been removed.
  23. Install the torque signal regulator valve spring (320), the torque signal regulator valve (321) and the PC solenoid valve (322) into the control valve body (301).
  24. Hold the PC solenoid valve (322) in the control valve body (301). Install the pressure control solenoid valve retainer (314E) into the control valve body (301).
    25. Fig 10: Identifying 1-2, 3-4 Shift Solenoid (SS) Valve Components
    GM840863Courtesy of GENERAL MOTORS CORP.
  25. Install a new O-ring seal (316) onto the 1-2, 3-4 shift solenoid (SS) valve (315A), if it was removed.
  26. Install the 1-2 shift valve spring (317), the 1-2 shift valve (318) and the 1-2, 3-4 SS valve (315A) into the control valve body (301).
  27. Hold the 1-2, 3-4 SS valve (315A) in the control valve body (301). Install the 1-2, 3-4 shift solenoid valve retainer (314D) into the control valve body (301).
    28. Fig 11: View Of Reverse Boost Valve Bushing Assembly Components
    GM840861Courtesy of GENERAL MOTORS CORP.
  28. Install the reverse boost valve (310), the line boost valve (304) and the line boost valve bore plug (303) into the reverse boost valve bushing (309).
  29. Install the pressure regulator valve (313), the pressure regulator valve outer and inner springs (311, 312) and the reverse boost valve bushing assembly (309) into the control valve body (301).
  30. Hold the reverse boost valve bushing assembly (309) in the control valve body (301). Install the line boost valve and bushing retainer (302) into the control valve body (301).
scientia non olet · About LEMON Manuals