|
Fastener Tightening Specifications:
Refer to Fastener Tightening Specifications . |
| Instrument Panel (I/P) Carrier Trim Cover Replacement Preliminary Procedures
- Disable the SIR. Refer to SIR Disabling and Enabling Zone 3
and SIR Disabling and Enabling Zone 5
in SIR.
- Remove the I/P insulators. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P compartment assembly. Refer to Compartment Assembly, Door, Striker, Latch Replacement - Instrument Panel .
- Remove the I/P driver knee bolster assembly. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P accessory trim plate. Refer to Accessory Trim Plate, Driver Information Display Switch Replacement - Instrument Panel .
- Remove the HVAC control module. Refer to HVAC Control Module Replacement
.
- Remove the radio. Refer to Radio Replacement
.
- Remove the driver information center. Refer to Accessory Trim Plate, Driver Information Display Switch Replacement - Instrument Panel .
- Remove the center I/P A/C outlets. Refer to Instrument Panel (I/P) Air Outlet Ducts Replacement
in Heating, Ventilation and Air Conditioning.
- Remove the I/P cluster trim plate. Refer to Cluster, Cluster Trim Plate Replacement - Instrument Panel .
- Remove the I/P lower trim molding. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P steering column opening moldings. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P upper trim pad. Refer to Upper Trim Pad, Outer Trim Cover, Fuse Block Access Cover Replacement - Instrument Panel .
|
| 1 |
Screw, I/P Carrier Trim Cover (Qty: 4) Tighten:
2 N.m (18 lb in)
|
| 2 |
Screw, I/P Carrier Trim Cover (Qty: 3) Tighten:
2 N.m (18 lb in)
|
| 3 |
Screw, I/P Carrier Trim Cover (Qty: 2) Tighten:
2 N.m (18 lb in)
|
| 4 |
Screw, I/P Carrier Trim Cover (Qty: 3) Tighten:
2 N.m (18 lb in)
|
| 5 |
Screw, I/P Carrier Trim Cover (Qty: 2)
Tip:
The two screws go up into the carrier cover, are located on each side of the passenger air bag module, and must be removed from inside of the I/P compartment opening.Tighten:
2 N.m (18 lb in)
|
| 6 |
Screw, I/P Carrier Trim Cover (Qty: 2)
Tip:
The two screws go up into the carrier cover and can be removed from the center A/C outlet opening.Tighten:
2 N.m (18 lb in)
|
| 7 |
Cover Assembly, I/P Carrier Trim |
| I/P Lower Extension Accessory Trim Panel Replacement Preliminary Procedures
- Disable the SIR. Refer to SIR Disabling and Enabling Zone 3
and SIR Disabling and Enabling Zone 5
in SIR.
- Remove the I/P insulators. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P compartment assembly. Refer to Compartment Assembly, Door, Striker, Latch Replacement - Instrument Panel .
- Remove the I/P driver knee bolster assembly. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P accessory trim plate. Refer to Accessory Trim Plate, Driver Information Display Switch Replacement - Instrument Panel .
- Remove the I/P A/C outlets. Refer to Instrument Panel (I/P) Air Outlet Ducts Replacement
in Heating, Ventilation and Air Conditioning.
- Remove the I/P cluster trim plate. Refer to Cluster, Cluster Trim Plate Replacement - Instrument Panel .
- Remove the I/P lower trim molding. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P steering column opening moldings. Refer to Knee Bolster, Insulator, Molding Replacement - Instrument Panel .
- Remove the I/P upper trim pad. Refer to Upper Trim Pad, Outer Trim Cover, Fuse Block Access Cover Replacement - Instrument Panel .
- Remove the I/P cup holder opening cover. Refer to Cup Holder, Cup Holder Door Replacement - Front Floor Console .
|
| 1 |
Screw, I/P Carrier Trim Cover (Qty: 4) Tighten:
2 N.m (18 lb in)
|
| 2 |
Screw, I/P Carrier Trim Cover (Qty: 3) Tighten:
2 N.m (18 lb in)
|
| 3 |
Screw, I/P Carrier Trim Cover (Qty: 2) Tighten:
2 N.m (18 lb in)
|
| 4 |
Screw, I/P Carrier Trim Cover (Qty: 3) Tighten:
2 N.m (18 lb in)
|
| 5 |
Screw, I/P Carrier Trim Cover (Qty: 2)
Tip:
The two screws go up into the carrier cover, are located on each side of the passenger air bag module, and must be removed from inside of the I/P compartment opening.Tighten:
2 N.m (18 lb in)
|
| 6 |
Screw, I/P Carrier Trim Cover (Qty: 2)
Tip:
The two screws go up into the carrier cover and can be removed from the center A/C outlet opening.Tighten:
2 N.m (18 lb in)
|
| 7 |
Cover Assembly, I/P Carrier Trim |
| 8 |
Screw, I/P Lower Extension Accessory Trim Panel (Qty: 4) Tighten:
2 N.m (18 lb in)
|
| 9 |
Screw, I/P Lower Extension Accessory Trim Panel (Qty: 2) Tighten:
2 N.m (18 lb in)
|
| 10 |
Panel Assembly, I/P Lower Extension Accessory Trim |