Cuts Out, Misses

WARNING: This page is about a different car, the 2004 Pontiac Grand Prix. However, it is still accessible from the selected car via links, so may be relevant.

Cuts Out, Misses

Inspections	Action
DEFINITION: Steady pulsation or jerking that follows engine speed, usually more pronounced as engine load increases. This condition is not normally felt above 1,500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or low speed.
Preliminary	Refer to Important Preliminary Inspections Before Starting in Symptoms - Engine Controls . Search for bulletins. Verify that the powertrain control module (PCM) grounds are clean, tight, and in the proper locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics . Remove the air filter element and inspect for dirt and for restrictions. Refer to Air Cleaner Element Replacement . Replace as necessary.
Fuel System	Test the fuel injectors. Refer to Fuel Injector Balance Test with Special Tool , Fuel Injector Balance Test with Tech 2 , and Fuel Injector Coil Test . Test for incorrect fuel pressure. Refer to Fuel System Diagnosis . Inspect for a restricted fuel filter. Refer to Fuel System Diagnosis . Inspect for a leaking fuel pressure regulator. Refer to Fuel System Diagnosis . Inspect for proper operation of the evaporative emission (EVAP) control system. Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) . Inspect for the following conditions that may cause the engine to run rich: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the HO2S connector Engine oil contaminated by fuel An EVAP canister purge condition Incorrect fuel pressure-Refer to Fuel System Diagnosis . A leaking fuel pressure regulator-Refer to Fuel System Diagnosis . Leaking fuel injectors-Refer to Fuel System Diagnosis . For proper operation of the manifold absolute pressure (MAP) sensor-Refer to Fuel System Diagnosis . For proper operation of the mass air flow (MAF) sensor-Refer to Scan Tool Data List and Scan Tool Data Definitions . Blockage on the inlet screen of the MAF sensor Vacuum hoses that are split, kinked, or improperly connected An air intake duct that is collapsed or restricted An air filter that is dirty or restricted-Refer to Air Cleaner Element Replacement . Inspect for the following conditions that may cause the engine to run lean: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the HO2S connector An exhaust leak between the HO2S and the engine-Refer to Exhaust Leakage in Engine Exhaust. Vacuum leaks Incorrect fuel pressure-Refer to Fuel System Diagnosis . Restricted fuel injectors-Refer to Fuel Injector Balance Test with Special Tool , Fuel Injector Balance Test with Tech 2 , and Fuel Injector Coil Test . For proper operation of the manifold absolute pressure (MAP) sensor-Refer to Manifold Absolute Pressure (MAP) Sensor Diagnosis (With Supercharger) or Manifold Absolute Pressure (MAP) Sensor Diagnosis (Without Supercharger) . An inaccurate MAF sensor-Refer to Scan Tool Data List and Scan Tool Data Definitions . Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) . Vacuum hoses that are split, kinked, or improperly connected
Sensor/System	Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity. Inspect the air intake ducts for being collapsed, damaged, loose, improperly installed, or leaking especially between the MAP sensor and the throttle body. Inspect for a vacuum leak. Inspect the exhaust gas recirculation (EGR) system for proper operation. Refer to Exhaust Gas Recirculation (EGR) System Description . Inspect the positive crankcase ventilation (PCV) valve operation.
Ignition System	Soak the secondary ignition system with water from a spray bottle. Soaking the secondary ignition system may help locate damaged or deteriorated components. Look and listen for arcing or misfiring as you apply water. Monitor the Misfire Current Counters while driving the vehicle in the conditions that the misfire occurred. If a misfiring cylinder can be located, use the DTC P0300 table for diagnosis. Refer to DTC P0300 . Test for proper ignition voltage output with the J 26792 Spark Tester. Remove the spark plugs and inspect for the following conditions: Correct heat range Wet plugs Cracks Wear Improper gap Burned electrodes Heavy deposits Refer to Spark Plug Inspection . An improper spark plug gap will cause a driveability problem. Refer to Ignition System Specifications . Gap the spark plugs using a wire gauge gap tool. Refer to Spark Plug Replacement and Ignition System Specifications . Determine the cause of the fouling before replacing the spark plugs. Visually and physically inspect the secondary ignition for the following conditions: The spark plug wires for signs of arcing/cross firing, cracks, carbon tracking, plug boot damage, pinched, improper routing, or a resistance value outside the specified range-Refer to Ignition System Specifications . The ignition wires for proper engagement to spark plug The ignition coils for cracks or carbon tracking
Engine Mechanical	Inspect engine mechanical for the following conditions: Test compression-Refer to Engine Compression Test in Engine Mechanical. Sticking or leaking valves Worn camshaft lobes Valve timing Bent push rods-Refer to Valve Rocker Arm and Push Rods Cleaning and Inspection in Engine Mechanical. Worn rocker arms -Refer to Valve Rocker Arm and Push Rods Cleaning and Inspection in Engine Mechanical. Broken valve springs-Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical. Excessive oil in combustion chamber, leaking valve seals For more information refer to one of the following procedures in Engine Mechanical: Engine Compression Test Symptoms - Engine Mechanical Oil Consumption Diagnosis For incorrect basic engine parts inspect the following components: The camshaft-Refer to Crankshaft and Bearings Cleaning and Inspection in Engine Mechanical. The cylinder heads-Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical. The pistons, etc.-Refer to Piston, Connecting Rod, and Bearings Cleaning and Inspection in Engine Mechanical.
Additional Inspections	Inspect the exhaust system for possible restrictions. Inspect for the following conditions: The exhaust system for damaged or collapsed pipes The mufflers for heat distress or possible internal failure For possible plugged catalytic converters-Refer to Restricted Exhaust in Engine Exhaust. Electromagnetic interference (EMI) on the reference circuit can cause an engine misfire condition. A sudden increase in indicated RPM with little change in actual engine RPM change indicates EMI is present. Inspect for high voltage components near ignition control circuits if a condition exists. Inspect the intake manifold and the exhaust manifold passages for casting flash.