LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2004 >> Century Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 137 (Automatic Transaxle - 4T65-E (Introduction, Service & Replacement)) >> Repair Instructions >> Automatic Transmission Range Selector Cable Replacement >> Installation Procedure

Installation Procedure

WARNING: This page is about a different car, the 2004 Pontiac Grand Prix. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Refer to Automatic Transaxle Range Selector Cable Caution in Cautions and Notices.
    Fig 1: Automatic Transmission Range Selector Cable
    GM161182Courtesy of GENERAL MOTORS CORP.
  1. Install the automatic transmission range selector cable through the hole in the cowl.
  2. Remove the mechanics wire from the end of the automatic transmission range selector cable.
    3. Fig 2: Automatic Transmission Range Selector Cable & Shift Control Lever
    GM161185Courtesy of GENERAL MOTORS CORP.
  3. If equipped with a steering column shift control, install the automatic transmission range selector cable to the shift control lever.
  4. Install the left knee bolster. Refer to Knee Bolster Replacement - Left in Instrument Panel, Gages and Console.
    5. Fig 3: Automatic Transaxle Range Selector Cable & Console Shift Control
    GM161220Courtesy of GENERAL MOTORS CORP.
  5. If equipped with a floor console shift control, install the automatic transaxle range selector cable to the console shift control bracket.
  6. Install the automatic transaxle range selector cable to the console shift control.
    7. Fig 4: Automatic Transaxle Range Selector Cable Retainer & Console Shift Control
    GM161221Courtesy of GENERAL MOTORS CORP.
  7. Install the automatic transaxle range selector cable retainer to the console shift control.
  8. Install the carpet into position. Refer to Carpet Replacement - Front in Interior Trim.
  9. Install the Front Floor Console. Refer to Console Replacement - Front Floor in Instrument Panel, Gages and Console.
    10. Fig 5: Positioning Automatic Transmission Range Selector Cable
    GM1244805Courtesy of GENERAL MOTORS CORP.
  10. Properly route and position the automatic transmission range selector cable.
    11. Fig 6: Identifying Automatic Transaxle Range Selector Cable To Cable Bracket
    GM629687Courtesy of GENERAL MOTORS CORP.
  11. Install the automatic transaxle range selector cable to the automatic transaxle range selector cable bracket.
  12. Install the automatic transaxle range selector cable to the automatic transaxle range selector lever.
    13. Fig 7: View Of Transaxle Range Selector Cable & Shift Lever
    GM629690Courtesy of GENERAL MOTORS CORP.
  13. Install the automatic transaxle range selector cable retainer.
    14. Fig 8: Inserting Metal End Fitting Of Shift Control Cable Into Transaxle Cable End
    GM161176Courtesy of GENERAL MOTORS CORP.
  14. Place the transaxle in the Neutral position.
  15. Place the shift control in the Neutral position.
  16. Connect each cable section to the following before connecting the two cable sections.
    • Insert the metal end fitting of the shift control cable into the transaxle cable end.
    • Use the molded end fittings to push the metal end fitting of the shift control cable and the transaxle cable end together until the metal post snaps into place.
  17. Depress the adjuster clip once. This mobilizes the adjuster housing toward the transaxle end fitting.
  18. Line up the end fittings so they slide together until you feel the parts come together and lock.
    19. Fig 9: Identifying Adjuster Clip
    GM161177Courtesy of GENERAL MOTORS CORP.
  19. Depress the adjuster clip completely. This locks the cable into its adjusted service position.
  20. Pull the conduit in the opposite direction to assure full system adjustment of the shift cable.
    21. Fig 10: Ensuring Conduit Is Fully Engaged
    GM161178Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: The horseshoe clip with the tab is flush when fully engaged.
  21. Ensure the conduit is fully engaged.
    22. Fig 11: Identifying Horseshoe Clip
    GM161179Courtesy of GENERAL MOTORS CORP.
  22. The horseshoe clip with the tab is not flush when not fully engaged.
    23. Fig 12: Automatic Transaxle Range Selector Cable
    GM161181Courtesy of GENERAL MOTORS CORP.
  23. Install the automatic transaxle range selector cable to the wiring harness clip or strap.
  24. Adjust the automatic transaxle range selector cable. Refer to Automatic Transmission Range Selector Cable Adjustment .
  25. Install the air cleaner intake duct. Refer to Air Cleaner Intake Duct Replacement in Engine Controls - 3.8L.
scientia non olet · About LEMON Manuals