Test Description

WARNING: This page is about a different car, the 2004 Pontiac Grand Prix. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

3: Listen for an audible click when the A/C compressor clutch relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
4: Tests for voltage at the coil side of the A/C compressor clutch relay. The 10-Amp fuse supplies power to the coil side of the A/C compressor clutch relay.
5: Verifies that the powertrain control module is providing ground to the A/C compressor clutch relay.
6: Tests if ground is constantly being applied to the A/C compressor clutch relay.
7: Tests for a short to voltage or an open.
13: Perform the programming procedure for the PCM.

DTC P0645

Step	Action	Yes	No
Schematic Reference: HVAC Schematics Connector End View Reference: HVAC Connector End Views
1	Did you perform the HVAC Diagnostic System Check?	Go to Step 2	Go to Diagnostic System Check - HVAC Systems - Manual
2	IMPORTANT: The ambient air temperature must be above 3°C (38°F). Turn OFF the ignition. Inspect the A/C compressor for free rotation operation. Start the engine. Place the HVAC control module in the OFF position. Does the A/C compressor operate?	Go to HVAC Compressor Clutch Does Not Disengage	Go to Step 3
3	Install a scan tool. Turn ON the ignition, with the engine OFF. With a scan tool, command the A/C Relay ON and OFF in the Special Functions, Engine Output Controls list. Does the A/C Relay turn ON and OFF with each command?	Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems	Go to Step 4
4	Turn OFF the ignition. Disconnect the A/C compressor clutch relay. Turn ON the ignition, with the engine OFF. Probe the ignition 3 voltage circuit of the A/C compressor clutch relay with a test lamp that is connected to a good ground. Does the test lamp illuminate?	Go to Step 5	Go to Step 11
5	Connect a test lamp between the control circuit of the A/C compressor clutch relay and the ignition 3 voltage circuit of the A/C compressor clutch relay. With a scan tool, command the A/C Relay ON and OFF. Does the test lamp turn ON and OFF with each command?	Go to Step 9	Go to Step 6
6	Does the test lamp remain illuminated with each command?	Go to Step 8	Go to Step 7
7	Test the control circuit of the A/C compressor clutch relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 14	Go to Step 10
8	Test the control circuit of the A/C compressor clutch relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 14	Go to Step 10
9	Inspect for poor connections at the A/C compressor clutch relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 14	Go to Step 12
10	Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 14	Go to Step 13
11	Repair the ignition 3 voltage circuit of the A/C compressor clutch relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair?	Go to Step 14	-
12	Replace the A/C compressor clutch relay. Refer to Compressor Relay Replacement in Heating, Ventilation and Air Conditioning. Did you complete the replacement?	Go to Step 14	-
13	IMPORTANT: Perform the programming procedure for the PCM. Replace the PCM. Refer to Powertrain Control Module (PCM) Replacement in Engine Controls.Did you complete the replacement?	Go to Step 14	-
14	Use the scan tool in order to clear the DTCs. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text. Does the DTC reset?	Go to Step 2	System OK