Install the sealing cap with radial shaft seal
NOTE:
TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents.
The sealing surfaces must be free of oil, grease and cleaning agents.
- Clean sealing surface (1) .
- Apply the sealant (1)
as shown on the special tool 2 469 803
.
Parts: Sealant
SEALING COMPOUND SPECIFICATION
| Loctite 5970 liquid sealing compound Processing time <10 minutes at room temperature |
50 ml, Cartridge | 83190404517 |
- Check the fitting sleeves (1)
for damage and that they are in the correct installation position.NOTE: TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents. - Clean sealing surface (2) .
- Apply the sealing compound on the contact edges of the separating plane for the oil pan (3)
.
- Make sure that the sealing cap (1) with the radial shaft seal is not stored for more than 6 months without support bushing (2) .
- Make sure that the support bushing (2)
stays in the sealing cap (1)
with the radial shaft seal until installation, as the support bushing (2)
is used as a slip bushing.
- Replace the sealing cap (1)
with the radial shaft seal.
Parts: Sealing cap with radial shaft seal.
- Coat the tire tread of the crankshaft with motor oil.
ENGINE OIL SPECIFICATION
| Technically suitable engine oils for BMW Group engines |
- Position the sealing cap (1) with the radial shaft seal and the support bushing (2) on the crankshaft and slide it on.
- Screws (2)
must only be replaced if M5x25 have been used.
Parts: Screws
- Replace screws (4)
.
Parts: Screws
- Abut the screws (1) to (4) .
- Tighten down screws (4) .
TIGHTENING TORQUES SPECIFICATION
| Upper oil sump section to crankcase (M8x45) | ||
|---|---|---|
| M8x45 screw Replace screw. |
tightening torque | 24 Nm |
- Tighten down screws (3) .
TIGHTENING TORQUES SPECIFICATION
| Upper oil sump section to crankcase (M6x25) | ||
|---|---|---|
| M6x25 screw | Joining torque | 10 Nm |
| Angle of rotation | 90° | |
- Tighten down screws (2) .
TIGHTENING TORQUES SPECIFICATION
| Sealing cap with radial shaft seal (M5x25) | ||
|---|---|---|
| M5x25 screw Replace screw. |
Tightening torque | 10 Nm |
TIGHTENING TORQUES SPECIFICATION
| Sealing cap with radial shaft seal (M6x30) | ||
|---|---|---|
| M6x30 screw | Tightening torque | 10 Nm |
- Tighten down screws (1) .
TIGHTENING TORQUES SPECIFICATION
| Sealing cap with radial shaft seal (M6x30) | ||
|---|---|---|
| M6x30 screw | Tightening torque | 10 Nm |
Follow-up work
- Refer to INSTALLING THE FLYWHEEL .
- Refer to INSTALLING FRONT PROPELLER SHAFT AT THE FRONT AXLE TRANSMISSION .
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING THE HEAT SHIELDS .
- Refer to INSTALLING CATALYTIC CONVERTER NEAR THE ENGINE ABOVE CYLINDER BANK 1 .
- Refer to INSTALLING UPPER CATALYTIC CONVERTER NEAR ENGINE FOR BANK 2 .
- Refer to INSTALLING HEAT SHIELD, TOP .
- Refer to INSTALLING EXPANSION TANK FOR THE CHARGE AIR COOLER .
- Refer to INSTALLING COOLANT EXPANSION TANK .
- Refer to INSTALLING THE HOLDER OF THE DME CONTROL UNIT FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING THE PRIMARY OXYGEN SENSOR FOR CYLINDERS 1 TO 4 .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE COVER PANEL OF THE SLAVE DME CONTROL UNIT .
- Refer to INSTALLING THE COVER PANEL OF THE MASTER DME CONTROL UNIT .
- Refer to INSTALLING THE CATALYTIC CONVERTER NEAR ENGINE, BOTTOM AT BANK 1 .
- Refer to INSTALLING THE CATALYTIC CONVERTER NEAR ENGINE, BOTTOM AT BANK 2 .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to ACTIVATING VEHICLE ELECTRICAL SYSTEM .
- Refer to CHECKING ENGINE OIL LEVEL .
- Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to REMOVING UNDERBODY PROTECTION AT SIDE RIGHT AND LEFT .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .