Install Wheel Arch

Pre-clean bonding surfaces on vehicle and on new part with cleaning agent R2.
CONSUMABLE SPECIFICATION

Cleaning agent R2 500 ml 83190417324
Clean bonding surfaces on vehicle and on new part with cleaning agent R1.
CONSUMABLE SPECIFICATION

Cleaning agent R1 100 ml, Bottle 83192211217
Apply adhesive K1 to the bonding surfaces.
ADHESIVE SPECIFICATION

Body adhesive K1 195 ml 83190413015
Install the new parts with an alignment bracket or a universal mount.
Rivet new parts in the areas (1) and (2) with blind rivets N2.
CONSUMABLE SPECIFICATION

Blind rivet N2
Ø 6.5 mm; clamping area 4.8-6.8 mm 83190301419

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet new parts in the areas (1) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new parts in the areas (1) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
For additional information see: 41 00...
Installation of a cavity sealing (not expanding)
Apply sealant D1 to the new cavity sealing (1) .
CONSUMABLE SPECIFICATION

Sealant D1 (seam sealing) 310 ml 83425A547B4

Courtesy of BMW OF NORTH AMERICA, INC.
Insert the cavity sealing (1) into the carrier support for the new part.
Apply sealant D1 to cavity sealing (1) . Consumable
Install the carrier support for the new part.
Rivet the new parts in the areas (1) and (2) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414
Rivet the new parts in the areas (3) with blind rivets N3.
CONSUMABLE SPECIFICATION

Blind rivet N3
Ø 4 mm; clamping area 1-3 mm 83190301421

Courtesy of BMW OF NORTH AMERICA, INC.
In the area (4) , use a bind rivet N6.
CONSUMABLE SPECIFICATION

Blind rivet N6
Ø 4 mm; clamping area 3-5 mm 83192158655
Weld the new parts in areas (1) according to the new part preparation process.
Avoid excessive application of heat to adhesive areas.

Courtesy of BMW OF NORTH AMERICA, INC.
Weld the new part in areas (1) according to the new part preparation process.
Avoid excessive application of heat to adhesive areas.

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet new parts in the areas (1) and (2) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet new parts in the areas (1) with blind rivets N1.

CONSUMABLE SPECIFICATION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm

83190301414

Courtesy of BMW OF NORTH AMERICA, INC.

Installing the EMC screw

Drill a hole with a diameter of 4.2 mm.
In the case of glued connections, only drill the hole after the adhesive has fully hardened.
Screw in the EMC screw.
CONSUMABLE SPECIFICATION

EMC screw SF Plus M5x15 83190301639
Seal the EMC screw with the sealant.

CONSUMABLE SPECIFICATION

Sealant D1 (seam sealing)

310 ml

83425A547B4

After the adhesive has hardened, install 3 EMC screws in the areas (1) shown.

CONSUMABLE SPECIFICATION

Screw
EMC screw, SF Plus, M5x15

83190301639

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to CUT THE THREADS .