Grease brake pads, brake anchor plate and brake caliper with brake pad paste
WARNING: This page is about a different car, the 2025 BMW M4, 2024 BMW M4, 2023 BMW M4, 2022 BMW M4, and 2021 BMW M4. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
- Clean contact surface (1) of the brake piston with brake cleaner and apply a thin coat of brake pad paste.CONSUMABLE DESCRIPTION
Brake block paste
* TU = Trade Unit. TU numbers cannot be ordered! For invoicing purposes only.3 g, Bag 83192158851 100 g, Tube 83192158852 5 g, TU* 83230140233 - Check dust boots for damage; replace if necessary.
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
- Clean contact surface (1) of the brake piston with brake cleaner and apply a thin coat of brake pad paste.
- Mount the sliding plates (1).
- Apply a thin coat of brake pad paste to the T-head of the inner brake pad in the areas (1) and (2).
- Apply a thin coat of brake pad paste to the T-head of the inner brake pad in the areas (1) and (2).
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
- Apply a thin coat of brake pad paste to the contact surface in the areas (1) and (2).
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
- Apply a thin coat of brake pad paste to the contact surface in the areas (1) and (2).
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
- Clean contact surface (1) of the brake piston with brake cleaner and apply a thin coat of brake pad paste.CONSUMABLE DESCRIPTION
Brake block paste * TU = Trade Unit. TU numbers cannot be ordered! For invoicing purposes only. 3 g, Bag 83192158851 100 g, Tube 83192158852 5 g, TU* 83230140233 - Check dust boots for damage; replace if necessary.
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
If brake pads are installed with an adhesive film, at this point they may only be cleaned and not greased with brake pad paste!
- Clean contact surface (1) of the brake piston with brake cleaner and apply a thin coat of brake pad paste.
- Mount the sliding plates (1).
- Apply a thin coat of brake pad paste to the T-head of the inner brake pad in the areas (1) and (2).
- Apply a thin coat of brake pad paste to the T-head of the inner brake pad in the areas (1) and (2).
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
- Apply a thin coat of brake pad paste to the contact surface in the areas (1) and (2).
NOTE:
TECHNICAL INFORMATION
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
If brake pads are installed with an adhesive film, they may not be greased with brake pad paste at position 2!
- Apply a thin coat of brake pad paste to the contact surface in the areas (1) and (2).