Remove injectors

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW M5, 2022 BMW M5, 2021 BMW M5, 2020 BMW M5, and 2019 BMW M5. However, it is still accessible from the selected car via links, so may be relevant.

Preliminary work

Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
Refer to REMOVING THE COVER PANEL OF THE MASTER DME CONTROL UNIT .
Refer to REMOVING THE COVER PANEL OF THE SLAVE DME CONTROL DEVICE .
Refer to REMOVING THE COVER IN THE ENGINE COMPARTMENT ON THE LEFT .
Refer to REMOVING THE COVER IN THE ENGINE COMPARTMENT ON THE RIGHT .
Refer to RELEASING LEFT FRONT-END STRUT .
Refer to RELEASING THE RIGHT FRONT-END STRUT .
Refer to REMOVING FRONT CROSS CONNECTION .
Refer to REMOVING LEFT INTAKE SILENCER HOUSING .
Refer to REMOVING RIGHT INTAKE SILENCER HOUSING .
Refer to REMOVING THE REAR TOP CROSS CONNECTION .
Refer to REMOVING FAN COWL WITH ELECTRIC MOTOR .
Refer to REMOVING THE ACOUSTIC COVER .
Refer to REMOVING HOLDER OF DME CONTROL UNIT FOR CYLINDERS 5 TO 8 .
Refer to PARTIALLY REMOVING THE COOLANT EXPANSION TANK .
Refer to REMOVING IGNITION COIL OF CYLINDER BANK 2 .
Refer to REMOVING RAIL FROM BANK 2 .
Refer to DISCONNECTING PLUG CONNECTIONS OF THE INJECTORS OF CYLINDER BANK 2 .

NOTE: RISK OF DAMAGE
Damage to injectors.
Excessive force may damage the injector and this means having to replace the injector.

Twist the injectors with a torsional movement of maximum 13 Nm.

NOTE: The description is provided only at one component. The procedure is the same for all other components.

NOTE: To provide a better overview: Shown with engine removed.

Loosen screw (1).
Remove hold-down device (2).
Pull injectors upward out of cylinder head and remove.
If several injectors are removed, ensure that each injector is reinstalled in its original installation location (cylinder):
Mark injectors.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
To not exceed the maximum tensile force of 2000 N when pulling out the fixed injectors: Use special tool 2 410 777 !
Using a correctly adjusted torque wrench and special tool 2 410 777 ensures that the maximum tensile force of 2000 N will not be exceeded at the injectors.
The injector must be replaced if the torque wrench clicks when the injector is pulled out.

Unscrew the pull-out thread (1) from the special tool 0 496 885 (13 0 320) .

Courtesy of BMW OF NORTH AMERICA, INC.
Screw in the pull-out thread (1) from special tool 0 496 885 (13 0 320) into special tool 2 410 777 .
Lightly oil the pull-out thread (1) before using the special tool 2 410 777 and unscrew completely as shown.
The pull-out threads (1) are left-hand threads.

Courtesy of BMW OF NORTH AMERICA, INC.
Position the special tool 2 410 777 on the injector shaft.
Screw in the screws (1) on the injector shaft for a few thread starts.
Fully screw in the pull-out thread (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Screw on the threaded sleeves (1) on to the injectors until the retaining pin (2) grips.

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the screws (2) and (3) of the special tool (1) 2 410 777 .

TIGHTENING TORQUES SPECIFICATION

Special tool 2 410 777 to injector well
M6	tightening torque	8 Nm

Check whether the pull-out threads (4) are fully screwed in.
Check whether the threaded sleeves (5) at the injectors are screwed on and retained.

Courtesy of BMW OF NORTH AMERICA, INC.
Adjust the torque wrench to 13 Nm in a clockwise rotation.
Position the torque wrench (1) and the special tool (2) 0 496 106 (11 8 720) on the hexagon head (3) of the special tool 2 410 777 .
Turn the torque wrench (1) in the direction of arrow until the injector is extracted.
If the torque wrench clicks while pulling the injector out, then the injector must be replaced!
Disassemble the special tool 2 410 777 and remove the injector.

Courtesy of BMW OF NORTH AMERICA, INC.