Install Rear Quarter Panel On Right

• Pre-clean the bonding surfaces (1)  on the new part and on the vehicle with solvent cleaner R2.

  CONSUMABLE SPECIFICATION 

  Cleaning agent R2

  500 ml

  83190417324

• Clean bonding surfaces (1)  on vehicle and on new part with cleaning agent R1.

  CONSUMABLE SPECIFICATION 

  Cleaning agent R1

  100 ml, Bottle

  83192211217

  Courtesy of BMW OF NORTH AMERICA, INC.

• Apply adhesive K5 to the bonding surfaces (1)  .

  ADHESIVE SPECIFICATION 

  Body adhesive K5

  50 ml

  83192158654

  NOTE: TECHNICAL INFORMATION 
  For additional information see: 41 00...
  Installation of cavity sealing (expanded)
• Apply sealant D2 to cavity sealing (2)  .

  CONSUMABLE SPECIFICATION 

  Sealant D2

  290 ml

  83425A547B9

• Install and locate side panel with a second person.

  During installation, ensure that sufficient adhesive has been applied to all bonding surfaces.

• Rivet side panel in areas (1)  to (4)  with blind rivets and punch rivets.

  Area	Description	Number
  1	N6	7
  2	N3	7
  3	N5	3
  4	N4	2

  CONSUMABLE SPECIFICATION 

  Blind rivet N6  Ø 4 mm; clamping area 3-5 mm

  83192158655

  Courtesy of BMW OF NORTH AMERICA, INC.

  CONSUMABLE SPECIFICATION 

  Blind rivet N3  Ø 4 mm; clamping area 1-3 mm

  83190301421

  CONSUMABLE SPECIFICATION 

  Punch rivet N5  Ø 5 mm; 5 mm long

  83192158079

  CONSUMABLE SPECIFICATION 

  Punch rivet N4  Ø 3 mm; 4 mm long

  83192457307

• Rivet the side panel in area (1)  with blind rivets N3.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rivet the side panel in area (1)  with blind rivets N3.
• Install an N5 punch rivet in each case in areas (2)  and (3)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Rivet the side panel in the areas (1)  to (3)  with punch rivets.

  Area	Description	Number
  1	N5	14
  2	N4	8
  3	N4	8

  Courtesy of BMW OF NORTH AMERICA, INC.

• Also apply K5 adhesive (2)  to the outer wheel arch section (3)  .

  (1)  = side panel wheel arch

  Courtesy of BMW OF NORTH AMERICA, INC.

• Flange the edge of wheel arch (3)  of the side panel flush to the outer wheel arch section.
• Do not create sharp edges when flanging because the crimping edge may otherwise begin to tear.
• Fill crimping edge fully with adhesive.

  Dimension (a)  = 5 mm

  (1)  = adhesive

  (2)  = rear quarter panel

• Seal the new part with sealant D2 in the same way as for standard production.

  Courtesy of BMW OF NORTH AMERICA, INC.

  Seal with sealant D2 in the area (3)  according to the standard.

  CONSUMABLE SPECIFICATION 

  Sealant D2

  290 ml

  83425A547B9

• Weld side panel in area (1)  .

  Avoid excessive heat input on the adjacent adhesive areas.

Courtesy of BMW OF NORTH AMERICA, INC.

Installing the EMC screw 

• Drill the hole with a diameter of 4.2 mm after the adhesive completely hardens.
• Screw in the EMC screw.

  CONSUMABLE SPECIFICATION 

  Screw  EMC screw, SF Plus, M5x15

  83190301639

• Seal the EMC screw with the sealant.

CONSUMABLE SPECIFICATION 

• After the adhesive has hardened, install 3 EMC screws in the areas (1)  .

CONSUMABLE SPECIFICATION 

Courtesy of BMW OF NORTH AMERICA, INC.