Removing the intake plenum

WARNING: High-voltage system .
The high-voltage system operates on the basis of hazardous, electrical voltage and high currents. Mortal hazard through electric shock!

All work on the high-voltage system may only be carried out by specially trained and technically experienced personnel.
For additional information see: SAFETY INSTRUCTIONS ON HANDLING HYBRID CARS .
For additional information see: NOTES ON REPAIR OF HIGH-VOLTAGE BATTERY UNIT .

WARNING: Working on 12 V electrical system .
Risk of short circuits! Risk of fire!

Make sure that there is no charger connected to the jump start terminal in the engine compartment.
Detach battery ground lead from battery.
For auxiliary batteries: Detach battery minus cables from all auxiliary batteries.

NOTE: RISK OF DAMAGE
Damage to battery terminal, the safety battery terminal or the intelligent battery sensor (IBS) .
Damaged battery terminals can lead to malfunctions or vehicle electrical system faults .

Detach battery terminal from battery pole by carefully shifting to and fro. Do not pry off using a tool.

Preliminary work

Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
Refer to REMOVING THE SEAL FOR THE HOOD REAR .
Refer to REMOVING THE ACOUSTIC COVER .
Refer to REMOVING ACOUSTIC COVER AT REAR .
Refer to REMOVING THE DME CONTROL UNIT .
Refer to REMOVING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
Refer to REMOVING CONTROL UNIT BRACKET .
Refer to REMOVING TANK VENT VALVE .
Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
Refer to REMOVING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
Refer to IF INSTALLED: REMOVE THE UNDERBODY PROTECTION OF THE STEERING SYSTEM .
Refer to DRAINING THE COOLANT FROM THE LOW-TEMPERATURE COOLING SYSTEM .
Refer to CONNECTING THE COOLANT LINES FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .

NOTE: RISK OF DAMAGE
Damage to wires when disconnecting connectors and plug connections .
Sheared wires can cause a short circuit .

Do not pull on wires when disconnecting connectors and plug connections.

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

Unlock plug connection (1) and disconnect.
Unlock plug connection (2) and disconnect.
Unlock and loosen clamp (3) .

Courtesy of BMW OF NORTH AMERICA, INC.
Remove screws (arrows).
Feed out charge air line (1) and place to one side.

Courtesy of BMW OF NORTH AMERICA, INC.

Loosen screw (1) .
Guide tank ventilation line (2) out of clamp (3) and remove it.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The tension rod screws and mounting bolts from the connecting neck on the intake plenum are not allowed to be opened.
Do not release screws (1) .

Courtesy of BMW OF NORTH AMERICA, INC.
Release the clamping collar (1) with the special tool 0 495 794 (17 2 050) .
Guide out the coolant hose (2) and remove it.
Catch and dispose of escaping coolant.
Unlock the locks (arrows).
Feed out the wiring harness section (3) for the sensor system 2 and set it aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock lock (1) .
Thread out holder (2) and set aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock plug connection (1) and disconnect.

Loosen screw (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock the locks (arrows).
Feed out the wiring harness section (1) for the injectors and ignition coils and put to one side.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen clamp (1) .
Feed out the wiring harness section (2) for the injectors and ignition coils and put to one side.

Courtesy of BMW OF NORTH AMERICA, INC.
Guide tank ventilation line (1) out of clamp (2) and place it aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen clamp (1) .

Feed out the wiring harness section (2) for the sensor system 1 and set it aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screw (1) .

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock plug connection (1) and disconnect.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock the locks (arrows).
Feed the tank ventilation line (1) out and set it aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock and release the coolant feed line (1) .

Catch and dispose of escaping coolant.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.
Loosen screws in the order (5) to (1) .
Guide out the intake plenum (A) and remove it.

Fig 1: Intake Plenum Screws Loosening Sequence
Courtesy of BMW OF NORTH AMERICA, INC.
Empty the remaining coolant (2) from the intake plenum (1) .

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The tension rod screws and mounting bolts from the connecting neck on the intake plenum are not allowed to be opened.
Do not release screws in the marked area on the intake plenum (1) .

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The tension rod screws and mounting bolts from the connecting neck on the intake plenum are not allowed to be opened.

Do not release screws in the marked area on the intake plenum (1) .

Courtesy of BMW OF NORTH AMERICA, INC.