Turning the piston to the TDC

WARNING: This page does not describe the selected car, but rather 10 other vehicles, including the 2024 BMW M340i xDrive, 2024 BMW M340i, 2023 BMW M340i xDrive, 2023 BMW M340i, and 2022 BMW M340i xDrive. However, it is still accessible from the selected car via links, so may be relevant.

WARNING: Hot surfaces .
Risk of burning!

Perform all work only on components that have cooled down.

WARNING: Working on 12 V electrical system .
Risk of short circuits! Risk of fire!

Make sure that there is no charger connected to the jump start terminal in the engine compartment.
Detach battery ground lead from battery.
For auxiliary batteries: Detach battery minus cables from all auxiliary batteries.

WARNING: Working on fuel system .
Risk of fire! Danger of explosion!

When working on the fuel system, make sure the workstation has sufficient ventilation, e.g., by means of extraction.
Tightly seal off open lines and connections; collect any leakage fuel directly at the point of exit.
No fire, sparks, open flames or smoking.

CAUTION: On releasing high pressure line, fuel may emerge at high speed .
Injury hazard!

Wear suitable personal protective equipment.
Before performing any installation work, allow cooling system to cool down to less than 40°C.
Note warnings on cylinder head cover.

NOTE: RISK OF DAMAGE
Damage to battery terminal, the safety battery terminal or the intelligent battery sensor (IBS) .
Damaged battery terminals can lead to malfunctions or vehicle electrical system faults .

Detach battery terminal from battery pole by carefully shifting to and fro. Do not pry off using a tool.

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

Preliminary work

Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
Refer to REMOVING THE SEAL FOR THE HOOD REAR .
Refer to REMOVING THE ACOUSTIC COVER .
Refer to REMOVING THE COVER OF THE ENGINE COMPARTMENT AT THE REAR LEFT .
Refer to REMOVING THE COVER OF THE REAR RIGHT ENGINE COMPARTMENT .
Refer to REMOVING LEFT AND RIGHT WIPER ARM .
Refer to REMOVING WINDSHIELD PANEL COVER .
Refer to REMOVING THE CENTER COWL UPPER PART .
Refer to REMOVING ACOUSTIC COVER AT REAR .
Refer to REMOVING THE CENTER BULKHEAD LOWER PART .
Refer to REMOVING THE DME CONTROL UNIT .
Refer to REMOVING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
Refer to REMOVING CONTROL UNIT BRACKET .
Refer to REMOVING SEAL FOR FRONT HOOD .
Refer to REMOVING THE COVER FOR THE CENTER ENGINE COMPARTMENT .
Refer to IF INSTALLED: PARTIALLY REMOVING THE TOP RIGHT AND LEFT COVER IN THE ENGINE COMPARTMENT .
Refer to REMOVING UPPER CROSS CONNECTION .
Refer to REMOVING THE REAR TOP CROSS CONNECTION .
Refer to REMOVING THE FAN COWL .
Refer to REMOVING ALL IGNITION COILS .
Refer to REMOVING THE HIGH PRESSURE LINE BETWEEN THE HIGH PRESSURE PUMP AND THE RAIL .
Refer to REMOVING FUEL DELIVERY LINE .
Refer to REMOVING HIGH PRESSURE PUMP .
Refer to REMOVING THE RAIL WITH INJECTORS OF CYLINDERS 1 TO 3 .
Refer to REMOVING THE RAIL WITH INJECTORS OF CYLINDERS 4 TO 6 .
Refer to REMOVING BOTH ACTUATORS .
Refer to REMOVING THE CYLINDER HEAD COVER .
Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
Refer to REMOVING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
Refer to IF INSTALLED: REMOVE THE UNDERBODY PROTECTION OF THE STEERING SYSTEM .
Refer to IF INSTALLED: PARTIALLY RELEASE THE ENGINE OIL COOLER .
Refer to DRAINING THE COOLANT FROM THE LOW-TEMPERATURE COOLING SYSTEM .
Refer to CONNECTING THE COOLANT LINES FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
Refer to IF INSTALLED: SECURING THE ENGINE OIL COOLER .
Refer to REMOVING TANK VENT VALVE .
Refer to REMOVING THE INTAKE PLENUM .

NOTE: RISK OF DAMAGE
Damage to the engine .
If the engine is manually rotated in the wrong direction of rotation, the engine can be damaged .

Only rotate the engine manually in the correct direction of rotation: a) clockwise when looking at the damper, or b) counterclockwise when looking at the chain drive, b) applies only if the timing chain is installed in the rear.

NOTE: TECHNICAL INFORMATION
The OT finder from the special tool 2 302 630 absolutely must be vertical, otherwise the measurement result can be falsified.

NOTE: The description is provided only at one cylinder. The procedure is the same for all other cylinders.

Keep set of special tools 2 302 630 at hand:

Number	Description
1	Pressure gauge
2	OT Finder
3	Adapter for the spark plug thread (60)
4	Adapter for the spark plug thread

Courtesy of BMW OF NORTH AMERICA, INC.

Have the special tool 0 493 380 (11 6 480) 2 468 560 ready.

Courtesy of BMW OF NORTH AMERICA, INC.
Have the adapter for the spark plug thread (60) (1) ready.

Courtesy of BMW OF NORTH AMERICA, INC.
Screw in the adapter for the spark plug thread (60) (1) into the spark plug thread by hand.

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the adapter for the spark plug thread (60) (1) with a standard tool (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Connect the OT finder (1) to the adapter for the spark plug thread (60) (2) .
The OT finder (1) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The OT finder from the special tool 2 302 630 absolutely must be vertical, otherwise the measurement result can be falsified.
Fit special tool 0 493 380 (11 6 480) .
Turn the engine by hand with the special tool 0 493 380 (11 6 480) .
If the piston goes upwards, the bubble level (2) in the cylinder tube (1) also goes upward in the arrow direction .
Turn the piston to TDC .
At TDC , both the piston and bubble level (2) are at the highest point in the cylinder tube (1) .

» Valves are closed.
Make sure the engine does not turn further.

Courtesy of BMW OF NORTH AMERICA, INC.