Install Engine Mount In Front Of Cowling With Wheel Arch

Preclean all bonding surfaces with solvent cleaner R2.
CONSUMABLE SPECIFICATION

Cleaning agent R2 500 ml 83190417324
Clean all bonding surfaces with solvent cleaner R1.
CONSUMABLE SPECIFICATION

Cleaning agent R1 100 ml, Bottle 83192211217
Apply adhesive K1 to bonding surfaces.
ADHESIVE SPECIFICATION

Body adhesive K1 195 ml 83190413015
During installation of the new parts, make sure that sufficient adhesive has been applied to all bonding surfaces.
Install the new part with an alignment bracket or a universal fixture.
Rivet the new parts in the areas (1) with three blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new part in the area (1) and (2) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Install new part and rivet in area (1) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new parts in the area (2) with blind rivet N2.
CONSUMABLE SPECIFICATION

Blind rivet N2
ø 6.5 mm; clamping area 4.8-6.8 mm 83190301419
Weld the new part in the areas (3).
Avoid excessive application of heat to adhesive areas
Weld the new part in the area (1).
Avoid excessive application of heat in this process.

The cowling cross-member (2) is filled with hardly inflammable cavity foam.
In case of smoke formation: Stop the welding procedure and cool the welded area with compressed air if applicable,

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new part in the areas (1) and (2) with blind rivets N1,
CONSUMABLE SPECIFICATION

Blind rivet N1
ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new part in the areas (1) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new part in the areas (1) with blind rivets N1.
CONSUMABLE SPECIFICATION

Blind rivet N1
ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Install the reinforcement plates (1) and attach by welding.
Observe the bonding surface (2) of the aluminum spring support.

Courtesy of BMW OF NORTH AMERICA, INC.
Install the new part section and weld it in the areas (Dto (3).
While doing so, observe the adhesive area (4) of the aluminum spring support.
Avoid applying too much heat to adjacent adhesive area (4).

Courtesy of BMW OF NORTH AMERICA, INC.
Install an EMC screw in area (1).
CONSUMABLE SPECIFICATION

screw
EMC screw, SF Plus, M5x15 83190301639

Courtesy of BMW OF NORTH AMERICA, INC.
Install an EMC screw in area (1).
CONSUMABLE SPECIFICATION

screw
EMC screw, SF Plus, M5x15 83190301639

Courtesy of BMW OF NORTH AMERICA, INC.