Install heat management module

NOTE: RISK OF DAMAGE
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .

Route all cables without abrasions, do not trap and crush.

NOTE: TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents.

NOTE: RISK OF DAMAGE
Damage to the surface .
The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage .

Do not use any metal-cutting tools.

Clean sealing surfaces (1) .

Courtesy of BMW OF NORTH AMERICA, INC.
Replace sealing rings (1) on connecting pipe (2) .
Parts: Sealing ring
Coat sealing rings (1) with coolant before installing.

Courtesy of BMW OF NORTH AMERICA, INC.
Replace sealing rings (1) on heat management module (2) .
Parts: Sealing ring
Coat the sealing rings (1) on the heat management module (2) with coolant before installing.

Courtesy of BMW OF NORTH AMERICA, INC.
Guide in and install the connecting pipe (1) in the arrow direction on the heat management module (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Insert and install the heat management module (1) with the connecting pipe (2) .
Make sure that the connecting pipe (2) is installed correctly.

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws (1) .

TIGHTENING TORQUE SPECIFICATION

Heat exchange module to crankcase
M6	Tightening torque	9 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Connect connector (1) to the knock sensor and lock it.
The connector (1) must engage audibly onto the knock sensor.
Secure clamps (2) .

Courtesy of BMW OF NORTH AMERICA, INC.
Connect and lock the coolant line (4) .
The coolant line (4) must engage audibly.
Secure the clamp (3) .
Connect connectors (1) and (2) to the heat management module and lock them.
The connectors (1) and (2) at the heat management module must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Feed in and install the grounding cable (2) .

Tighten nut (1) .

TIGHTENING TORQUE SPECIFICATION

Grounding cable on the starter motor generator
M8	tightening torque	19 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Secure the clamp (3) .
Connect and lock coolant lines (1) and (2) .
The coolant lines (1) and (2) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Connect and lock coolant line (1) .
The coolant line (1) must engage audibly.

Courtesy of BMW OF NORTH AMERICA, INC.
Guide in and install the support (2) for the intake plenum.

Tighten down screws (1) .

TIGHTENING TORQUE SPECIFICATION

Support to cylinder head
M6X16	tightening torque	8 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Secure clamps (1) .
Secure clamps (2) .

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE INTAKE PLENUM .
Refer to INSTALLING THE TANK VENT VALVE .
Refer to INSTALLING CONTROL UNIT BRACKET .
Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
Refer to INSTALLING THE DME CONTROL UNIT .
Refer to INSTALLING INTAKE FILTER HOUSING .
Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
Refer to FILLING AND VENTING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
Refer to FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT .
Refer to INSTALLING ACOUSTIC COVER AT REAR .
Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
Refer to INSTALLING ACOUSTIC COVER .
Refer to IF INSTALLED: INSTALL UNDERBODY PROTECTION FOR THE STEERING .
Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
Refer to INSTALLING FRONT UNDERBODY PROTECTION .
Refer to TAKING HOOD OUT OF THE SERVICE POSITION .