Install heat management module

• Clean the sealing surfaces (1)  on the crankcase with the special tool 0 495 102 (11 4 470)  .
• Replace the sealing rings (1)  .

  Parts:  Sealing rings

• Feed in the sealing rings (1)  at the heat management module (2)  and install.

  Courtesy of BMW OF NORTH AMERICA, INC.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Correctly position the heat management module (2)  .
• Hand-tighten the bolts (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the screws (1)  on the heat management module (2)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Heat exchange module to crankcase
  M6	Tightening torque	9 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: RISK OF DAMAGE 
  Improper routing of cables and wiring harnesses  .
  Trapped, crushed or damaged cables may cause short circuits and malfunctions  .

  • Route all cables without abrasions, do not trap and crush.
• Insert and position wiring harness section (4)  for sensor system 1  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure clamps (3)  .
• Connect connectors (1)  to (2)  and lock.

  Make sure you can hear the connectors (1)  and (2)  engage.

• Guide in and position the coolant line (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Lock the coolant line (1)  .

The coolant line (1)  must audibly engage.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE COMPLETE FULL-FLOW OIL FILTER .
• Refer to INSTALLING THE THERMOSTAT ON THE TRANSMISSION OIL LINES .
• Refer to INSTALLING THE OIL FILTER ELEMENT .
• Refer to INSTALLING THE INTAKE PLENUM .
• Refer to INSTALLING THE TANK VENT VALVE .
• Refer to INSTALLING CONTROL UNIT BRACKET .
• Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
• Refer to INSTALLING THE DME CONTROL UNIT .
• Refer to INSTALLING THE ACOUSTIC COVER FOR THE ENGINE AT THE FRONT .
• Refer to INSTALLING CHARGE AIR LINE .
• Refer to INSTALLING THE CLEAN AIR PIPE WITH THE RESONATOR .
• Refer to TOPPING UP THE MOTOR OIL .
• Refer to INSTALLING THE OIL FILLER CAP .
• Refer to CONNECTING NEGATIVE BATTERY CABLE OF THE SYSTEM BATTERY .
• Refer to ACTIVATING HIGH-VOLTAGE SYSTEM .
• Refer to INSTALLING FLAP IN RIGHT LUGGAGE COMPARTMENT TRIM PANEL .
• Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
• Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
• Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
• Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
• Refer to CHECKING ENGINE OIL LEVEL .
• Refer to INSTALLING ACOUSTIC COVER AT REAR .
• Refer to INSTALLING THE CENTER COWL UPPER PART .
• Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
• Refer to INSTALLING WINDSHIELD PANEL COVER .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to IF INSTALLED: INSTALL UNDERBODY PROTECTION FOR THE STEERING .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
• Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .