Installing the catalytic converter near engine, bottom at bank 2

• Feed in the catalytic converter near engine (2)  upwards.
• Position the catalytic converter near engine (2)  on the stud bolt.
• Tighten nuts (1)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Bottom catalytic converter
  Nut M8 Replace nuts.	tightening torque	23 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace V-band clamp.

  Parts:  V-band clamp

• Replace gasket.

  Parts:  Seal

• Slide the V-clip (1)  towards the bottom onto the catalytic converter near engine.
• Position the V-clip (1)  on the catalytic converter near engine.
• Tighten down screw (2)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Top catalytic converter to bottom catalytic converter
  V-band clamp Replace V-band clamp.	Tightening torque	14 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Installing the version with gasoline particulate filter for cylinders 5 to 8 

Installing the differential pressure sensor of the cylinders 5 to 8 

• Replace molded hose (1)  .

  Parts:  Molded hose

• Grease the thread on the exhaust system with high-temperature assembly paste.
  CONSUMABLE SPECIFICATION
  
  

  High-temperature assembly paste

  10 g, Tube

  83230309003

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in the differential pressure sensor with pressure line downwards.
• Clip the pressure line (2)  into the clamps (3)  .
• Tighten nut (1)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Pressure line on catalytic converter
  Pressure line	Tightening torque	40 Nm

• Clip in the hose (4)  into the clamp (3)  .
• Connect connectors (1)  and lock.
• Tighten nut (2)  .
  TIGHTENING TORQUE SPECIFICATION
  
  

  Differential pressure sensor to holder
  Nut M6	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING HEAT SHIELD, TOP .
• Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE LAMBDA OXYGEN SENSOR FOR CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE CROSSING OF THE TRANSMISSION WIRING HARNESS .
• Refer to INSTALLING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE .
• Refer to INSTALLING BRACKET FOR RIGHT INTAKE SILENCER .
• Refer to INSTALLING OIL FILLER NECK .
• Refer to FASTENING THE ENGINE VENTILATION LINE OF CYLINDER BANK 1 .
• Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
• Refer to INSTALLING THE OXYGEN SENSOR MONITOR FOR CYLINDERS 5 TO 8 .
• Refer to FASTENING THE ACTIVATED-CHARCOAL FILTER LINE .
• Refer to FASTENING THE ENGINE VENTILATION LINE OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
• Refer to FASTENING THE ENGINE VENTILATION LINE OF CYLINDER BANK 2 .
• Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING FRONT PROPELLER SHAFT AT THE FRONT AXLE TRANSMISSION .
• Refer to INSTALLING THE TRANSFER BOX (ATC 13-1) .
• Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
• Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
• Refer to INSTALLING TRANSMISSION CROSS MEMBER .
• Refer to ACTIVATING VEHICLE-SPECIFIC HIGH-VOLTAGE OR LOW-VOLTAGE VEHICLE ELECTRICAL SYSTEM .
• Refer to CHECKING/TOPPING UP THE TRANSFER BOX OIL (ACTIVE TORQUE CONTROL 13-1) .
• Refer to INSTALLING THE AIR DUCT .
• Refer to INSTALLING THE HEAT SHIELDS .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE REAR LEFT AND RIGHT TENSION STRUT .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING LEFT STRUT BRACE .
• Refer to INSTALLING ACOUSTIC COVER .