Taking engine out of installation position

• When lowering the engine, guide the engine mount (1) in the front subframe.
• Make sure that the plastic of the engine mount (1) is not damaged.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Lower the engine by turning the spindle 2 361 506 (00 6 103)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Engine mount to front axle support
  M8
  	tightening torque  19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the screw (1) of the right engine mount with a standard tool.
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Engine mount to engine support bracket
  M12
  	tightening torque  100 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install the right reinforcement strut (2).
• Tighten down screw (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Engine mount reinforcement strut on front subframe
  M12
  	tightening torque  110 Nm

• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Engine mount reinforcement strut on body
  M12
  	tightening torque  110 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Release the special tool 0 490 567 (11 0 020) from the engine bridge.
• Release and remove the special tool 0 490 567 (11 0 020) from the mounting brackets (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  Installing intake filter housing 

  Prerequisite 

  Ignition is switched off.

• Check rubber mount (1) for correct fit in the intake filter housing.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in the cable of the Lambda oxygen sensors through the opening (arrow) on the intake filter housing (1).
• Connect intake filter housing (1) with the clean air pipes (2).
• Install intake filter housing (1) and fasten in the rubber mounts (markings).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten clamps (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Clean air pipe to upper section of intake filter housing
  cl.
  	tightening torque  3 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach the cable (4) of the Lambda oxygen sensor to the clamps.
• Attach the connector (2) to the holder (3) and lock. The connectors (2) must engage audibly.
• Connect the connector (1) of the Lambda oxygen sensors and lock.

  The connectors (1) must engage audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

  Install acoustic cover 

  NOTE: RISK OF DAMAGE 
  Damage to the acoustic cover/design cover  .
  Jerky movements during disassembly and application of excessive force during installation may result in breakage of the acoustic cover/design cover  .

  • Disassemble or mount the acoustic cover/design cover carefully.
  • Disassemble or mount snap-lock couplings of the ball pivots one after the other.
  • Disassemble or mount the acoustic cover/design cover only at temperatures > 20°C.
  • Use only distilled water as an auxiliary material during installation, no lubricants.
• Check acoustic cover for correct seating of the rubber mount (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check rubber mount (1) and (2) for correct fit.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Clip the acoustic cover (1) in the holder.

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING REAR SECTION OF THE FRONT RIGHT WHEEL ARCH COVER .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE RIGHT .
• Refer to PARTIALLY INSTALLING THE FRONT RIGHT WHEEL ARCH TRIM (DOOR SILL) .
• Refer to INSTALLING THE FRONT RIGHT WHEEL .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT , and INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE TOP RIGHT .
• Refer to INSTALLING THE FRONT HOOD SEAL .
• Refer to INSTALLING THE STRUT BRACE ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE CENTER COWL UPPER PART .
• Refer to INSTALLING WINDSHIELD PANEL COVER .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
• Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .