Install the wiring harness section of the transmission wiring harness
Wiring harness section of transmission wiring harness
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .
Improper routing of cables and wiring harnesses .
Trapped, crushed or damaged cables may cause short circuits and malfunctions .
- Route all cables without abrasions, do not trap and crush.
- Insert and install the wiring harness (1)
for the transmission module.
- Feed in and install the wiring harness section (2) of the transmission wiring harness.
- Secure clamps (1)
.
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Secure clamp (arrow).
- Thread in the wiring harness section (2) of the supply module and install.
- Secure clamp (arrow).
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
Fastening the transmission
- Move the transmission (3) to the installation position.
- Replace screws (2)
.
Parts: Screws
- Tighten down screws (2) .
TIGHTENING TORQUE SPECIFICATIONS
| Transmission cross member to body | ||
|---|---|---|
| M8 | tightening torque | 19 Nm |
- Secure the cable with the clamp (1) .
- Loosening the luggage strap (1) .
- Remove special tools 2 219 012
and 0 495 498 (23 4 050)
.
- Connect connectors (1)
and lock.
- Guide in and position cover (3) .
- Tighten down screw (2) .
TIGHTENING TORQUE SPECIFICATIONS
| Cover to transmission cross member | ||
|---|---|---|
| Hexagon screw M8 Replace screw. |
Tightening torque | 19 Nm |
- Fasten the holder (1) .
- Guide in and install wiring harness section (2) of the transmission wiring harness.
- Secure the clamps (arrows).
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Fasten the cable clip (1)
.
- Feed in and install the wiring harness section (3) of the transmission wiring harness.
- Make sure that the lock (2) engages correctly.
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Cable bracket on rear cylinder head/transmission | ||
|---|---|---|
| M6 x 20 | tightening torque | 8 Nm |
- Secure the clamps (arrows).
- Feed in the cable bracket (2)
and install it.
The lock (1) must engage audibly.
- Feed in the cable bracket (2) and install it.
The locks (1) must engage audibly.
Follow-up work
- Refer to INSTALLING THE CONTROL UNIT HOLDER .
- Refer to PARTIALLY INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING THE COVER FOR THE DME CONTROL UNIT .
- Refer to INSTALLING THE STRUT BRACE .
- Refer to INSTALLING CENTER BULKHEAD LOWER PART .
- Refer to INSTALLING THE CENTER COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE REAR HOOD SEAL .
- Refer to INSTALLING TRANSMISSION MOUNTING BRACKET (ALL-WHEEL DRIVE VEHICLE) .
- Refer to INSTALLING THE TRANSMISSION BEARING SUPPORT .
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING FRONT HEAT SHIELD .
- Refer to INSTALLING THE REAR HEAT SHIELD .
- Refer to INSTALLING THE LEFT THRUST FIELD .
- Refer to INSTALLING TANK COVER .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING THE LEFT AND RIGHT FRONT UNDERSHIELD .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT SPOILER .