Install the rear end cover

Remove the sprayed on sealing bead (1) on the end cover.
NOTE: TECHNICAL INFORMATION
The processing time of the liquid sealing compound can be at a maximum of 10 min.
Commissioning of the assembly is not possible until 25 minutes after the processing time.
Non-observance can lead to leaks in the assembly.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
For additional information see: OVERVIEW OF CONSUMABLES (BMW PARTS CATALOGUE) .

Apply a sealing bead with liquid sealing compound (1) on the end cover with a thickness of approximately 2.5 mm.

SEALING COMPOUND DESCRIPTION

Loctite 5970 liquid sealing compound Processing time <10 minutes at room temperature

50 ml, Cartridge

83190404517

Clean the sealing surface on the crankcase using the special tool 0 495 102 (11 4 470) .
Position the end cover (2) .
Tighten the screws in this area (1) .

TIGHTENING TORQUE SPECIFICATIONS

End cap (coolant) to crankcase (transmission side)
M6	Tightening torque	10 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE FLYWHEEL .
Refer to INSTALLING AUTOMATIC TRANSMISSION (ALL-WHEEL DRIVE VEHICLE) (GA8HP95Z) .
Refer to INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 7 TO 12 .
Refer to SECURING THE JUNCTURE SHAFT IN FRONT ON THE FRONT AXLE DIFFERENTIAL .
Refer to INSTALLING THE CATALYTIC CONVERTER FOR CYLINDERS 1 TO 6 .
Refer to INSTALLING THE TRANSFER BOX (ATC 13-1) .
Refer to CHECKING/TOPPING UP THE TRANSFER BOX OIL (ACTIVE TORQUE CONTROL 13-1) .
Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
Refer to INSTALLING TRANSMISSION CROSS MEMBER .
Refer to SCREW THE TRANSMISSION BEARING SUPPORT TIGHT (ALL-WHEEL DRIVE VEHICLE) .
Refer to INSTALLING THE HEAT SHIELDS .
Refer to CONNECTING TRANSMISSION OIL LINES .
Refer to INSTALLING EXHAUST SYSTEM .
Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
Refer to INSTALLING BOTH TRIM PIECES FOR THE EXHAUST TAILPIPE .
Refer to INSTALLING THE TRIM ON THE REAR BUMPER PANEL .
Refer to INSTALLING THE REAR DIFFUSER .
Refer to INSTALLING THE STIFFENING PLATE .
Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
Refer to CONNECTING ALL BATTERY GROUND LEADS .
Refer to FILLING THE COOLING SYSTEM WITH THE VACUUM FILLING UNIT .
Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
Refer to INSTALLING THE UNDERBODY PLANKING OF THE TRANSMISSION ON THE SIDE .
Refer to INSTALLING REAR UNDERBODY PROTECTION .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
Refer to INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
Refer to INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
Refer to INSTALLING THE RIGHT-HAND CHARGE AIR PIPE .
Refer to INSTALLING CHARGE AIR PIPE ON LEFT .
Refer to INSTALLING TOP RIGHT CLEAN AIR PIPE .
Refer to INSTALLING TOP CLEAN AIR PIPE ON LEFT .
Refer to INSTALLING THE RIGHT THROTTLE BODY .
Refer to INSTALLING THE LEFT THROTTLE BODY .
Refer to INSTALLING THE CENTER COWL UPPER PART .
Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Refer to INSTALLING FAN COWL .
Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
Refer to INSTALLING LEFT INTAKE PORT .
Refer to INSTALLING THE LEFT-HAND AIR DUCT .
Refer to INSTALLING RIGHT AIR DUCT .
Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
Refer to INSTALLING FANFARE HORN, RIGHT .
Refer to INSTALLING THE FANFARE ON THE LEFT SIDE .
Refer to INSTALLING THE CENTER TOP CROSS CONNECTION .
Refer to INSTALLING BOTH HEADLIGHTS .
Refer to INSTALLING BUMPER COVER, FRONT .
Refer to INSTALLING FRONT SECTION OF THE FRONT WHEEL ARCH COVER (PARTIALLY REMOVED) .
Refer to INSTALLING FRONT ORNAMENTAL GRILLE .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
Refer to ADJUSTING HEADLIGHTS .
Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
Refer to INSTALLING ACOUSTIC COVER .
Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
Refer to DELETE FAULT MEMORY .