Remove turbocharger

WARNING: Hot surfaces.
Risk of burning!

Perform all work only on components that have cooled down.

NOTE: RISK OF DAMAGE
Electrostatic discharge .
Damage to or destruction of electrical components .

Leave the electrical components in their original packaging until they are being installed. Only use the original packaging for returning the product. Always package removed components straight away.
Read and comply with user information on using the associated special tool 12 7 060.
Only tap the housings of electrical components. Do not tap pins or multi-pin connectors directly.
Wear electrically conductive clothing and antistatic shoes (with ESD symbol).
For additional information see: NOTES ON ESD PROTECTION (ELECTRO STATIC DISCHARGE) .

NOTE: TECHNICAL INFORMATION
Prior to replacing the turbocharger: Observe the notes on troubleshooting on the turbocharger .

NOTE: TECHNICAL INFORMATION
For turbocharger damage: Check the pressure pipes, charge air cooler and intake plenum for foreign matter, damage and correct functionality.
If the oil return line is exchanged, then the connecting pipe to the oil sump must ALWAYS be cleaned, as the connecting pipe can coke.

Preliminary work

Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
Refer to REMOVING THE SEAL FOR THE HOOD REAR .
Refer to REMOVING THE ACOUSTIC COVER .
Refer to REMOVING ACOUSTIC COVER AT REAR .
Refer to REMOVING THE FRONT HOOD SEAL .
Refer to REMOVING THE COVER FOR THE CENTER ENGINE COMPARTMENT .
Refer to REMOVING UPPER CROSS CONNECTION .
Refer to REMOVING THE REAR TOP CROSS CONNECTION .
Refer to REMOVING THE FAN COWL .
Refer to REMOVING INTAKE SILENCER HOUSING .
Refer to REMOVING ENGINE VENTILATION LINE .
Refer to REMOVING CLEAN AIR PIPE .
Refer to REMOVING CHARGE AIR LINE .
Refer to REMOVING THE ADAPTER FOR ENGINE VENTILATION LINE WITH HEATING ELEMENT ON TURBOCHARGER .
Refer to PARTIALLY RELEASING THE HOLDER OF THE POSITIVE BATTERY CABLE .
Refer to REMOVING THE OXYGEN SENSOR MONITOR .
Refer to REMOVING THE LAMBDA OXYGEN SENSOR .
Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
Refer to REMOVING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
Refer to IF INSTALLED: REMOVING THE UNDERBODY PROTECTION OF THE STEERING SYSTEM .
Refer to REMOVING THE CENTER UNDERBODY PROTECTION .
Refer to REMOVING REAR UNDERBODY PROTECTION .
Refer to REMOVING THE COVER OF THE STEERING ASSEMBLY .
Refer to REMOVING THE OIL RETURN LINE FOR THE TURBOCHARGER .
Refer to REMOVING TANK COVER ON LEFT AND RIGHT .
Refer to REMOVING STIFFENING STRUT .
Refer to REMOVING COMPLETE EXHAUST SYSTEM .
Refer to REMOVING CATALYTIC CONVERTER .
Refer to DRAINING THE COOLANT FROM THE HIGH-TEMPERATURE COOLING SYSTEM .
Refer to CONNECTING THE COOLANT LINE TO THE HIGH-TEMPERATURE COOLANT RADIATOR .

Turbocharger

Courtesy of BMW OF NORTH AMERICA, INC.

CAUTION: Heavy component.
Heavy components can lead to injury or damage.

Remove and install heavy components with the aid of another person/other persons.

NOTE: RISK OF DAMAGE
Damage of the electric wastegate valve controller .
Excessive force when removing and installing a jammed turbocharger may damage the electric wastegate valve controller .

Do not pull on the electrical wastegate valve controller or on the coupling rod.
Apply force only at the turbine housing and exhaust manifold.
Do not pull on the compressor housing.

NOTE: TECHNICAL INFORMATION
Do not damage the thermal compensating elements. Disassembly and installation including intermediate storage of the turbocharger is only permitted with mounted special tool 2 466 919.

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

Loosen screws (1).
Loosen screw (2).
Feed out and remove the heat shield (3).

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Feed out and remove the heat shield (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock and release the coolant return line (1) to the coolant pump (2) for the turbocharger.
Catch and dispose of leakage coolant.

Courtesy of BMW OF NORTH AMERICA, INC.
Release the screw (1) at the coolant return line (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screw (1).
Feed out the oil feed line (2) for the turbocharger and set it aside.
Catch and dispose of emerging motor oil.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1) and (2).
Feed the coolant feed line for the turbocharger (3) out of the crankcase and place aside.
Catch and dispose of leakage coolant.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1) and (2).
Feed out the support (3) and remove it.

Courtesy of BMW OF NORTH AMERICA, INC.
Ready the special tool 2 446 919 and the special tool 2 466 467 .

Courtesy of BMW OF NORTH AMERICA, INC.
Install the special tool 2 446 919 on the turbocharger and secure it with the bolt (1).
Make sure that the special tool 2 446 919 is flush with the turbocharger in the marked area .

Courtesy of BMW OF NORTH AMERICA, INC.
Secure the special tool 2 446 919 by turning the clamping lever (1) in the direction of the arrow .
NOTE: The clamping lever that is shown in the graphic is already in its end position.

Courtesy of BMW OF NORTH AMERICA, INC.
Position the holder (1) and fasten it with the bolt (2).
NOTE: The holder is used for the final mounting of the special tool 2 446 919 .

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the nut (1) hand-tight.
Tighten the nut (2) hand-tight.
Make sure that the special tool 2 466 467 is correctly positioned on the turbocharger (3).

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten the nut (1) hand-tight.
Tighten the nut (2) hand-tight.
Make sure that the special tool 2 466 467 is correctly positioned on the turbocharger (3).

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten nut (1) with standard tools (2).

TIGHTENING TORQUES SPECIFICATION

Special tool 2 466 467 on special tool 2 446 919
M8	tightening torque	5 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten nut (1) with standard tools (2).

TIGHTENING TORQUES SPECIFICATION

Special tool 2 466 467 on special tool 2 446 919
M8	tightening torque	5 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten nut (1) with standard tools (2).

TIGHTENING TORQUES SPECIFICATION

Special tool 2 466 467 on special tool 2 446 919
M8	tightening torque	5 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten nut (1) with standard tools (2).

TIGHTENING TORQUES SPECIFICATION

Special tool 2 466 467 on special tool 2 446 919
M8	tightening torque	5 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
Exhaust manifold/turbocharger is not bolted to the underside, but clamped instead. When removing/replacing the exhaust manifold/turbocharger, the trim strip remains screwed on.

Release the nut in the sequence (7) to (1).
Secure turbocharger against falling down.

Fig 1: Turbocharger Nuts Loosening Sequence
Courtesy of BMW OF NORTH AMERICA, INC.
Guide out and remove the sliding frame (1).

Courtesy of BMW OF NORTH AMERICA, INC.
CAUTION:
Heavy component.
Heavy components can lead to injury or damage.
- Remove and install heavy components with the aid of another person/other persons.
Courtesy of BMW OF NORTH AMERICA, INC.
Carefully guide out and remove the turbocharger (1).
Thermal compensating element of the turbocharger (1) or the exhaust manifold should not be bent or deformed.
Feed out and remove the seal (1) in the marked area .

Courtesy of BMW OF NORTH AMERICA, INC.