Remove the engine wiring harness for sensor system 1
NOTE:
TECHNICAL INFORMATION
Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.
Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.
NOTE:
TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.
Preliminary work
- Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
- Refer to REMOVING THE COVER OF THE ENGINE COMPARTMENT AT THE REAR LEFT .
- Refer to REMOVING THE COVER OF THE REAR RIGHT ENGINE COMPARTMENT .
- Refer to DEACTIVATING THE 48 V ELECTRICAL SYSTEM .
- Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
- Refer to REMOVING LEFT AND RIGHT WIPER ARM .
- Refer to REMOVING THE COWL COVER .
- Refer to REMOVING THE CENTER COWL UPPER PART .
- Refer to REMOVING SUSPENSION STRUT BRACE .
- Refer to REMOVING TRAILING LINK AT SPRING BOLT .
- Refer to REMOVING THE ENGINE CONTROL UNIT COVER .
- Refer to REMOVING THE ACOUSTIC COVER .
- Refer to REMOVING ACOUSTIC COVER AT REAR .
- Refer to REMOVING TANK VENT VALVE .
- Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
- Refer to REMOVING THE STIFFENING PLATE .
- Refer to REMOVING REAR UNDERBODY PROTECTION .
- Refer to REMOVING THE ACOUSTIC COVER OF THE OIL SUMP .
- Refer to REMOVING THE COVER OF THE STEERING ASSEMBLY .
- Refer to DRAINING THE COOLANT FROM THE LOW-TEMPERATURE COOLING SYSTEM .
- Refer to CONNECTING THE COOLANT LINE TO THE AUXILIARY COOLANT PUMP .
- Refer to REMOVING LOW-TEMPERATURE COOLANT EXPANSION TANK .
- Refer to REMOVING THE INTAKE PLENUM .
Engine wiring harness for sensor system 1
NOTE:
RISK OF DAMAGE
Damage to wires when disconnecting connectors and plug connections .
Sheared wires can cause a short circuit .
Damage to wires when disconnecting connectors and plug connections .
Sheared wires can cause a short circuit .
- Do not pull on wires when disconnecting connectors and plug connections.
- Unlock and disconnect plug connections (1) .
- Unlock plug connection (2) and disconnect.
- Unlock and loosen the cable clip (3) .
- Loosen the clamp (arrow).
- Feed out engine wiring harness (4)
of sensor system 1 and set aside.
- Loosen clamp (1) .
- Loosen clamps (2)
.
- Release the screws (1) .
- Feed out the support (2)
for the intake plenum and remove it.
- Unlock and disconnect plug connections (1) .
- Unlock plug connection (2) and disconnect.
- Unlock plug connection (3) and disconnect.
- Release the clamps (arrows).
- Unlock and disconnect the plug connections (1) and (2) .
- Release the clamps (arrows).
- Unlock and disconnect plug connections (1) .
- Unlock plug connection (2) and disconnect.
- Unlock plug connection (3) and disconnect.
- Release the clamps (arrows).
- Loosen screws (1) .
- Unlock the lock (arrow).
- Remove the wiring harness section (2)
and put to one side.
- Loosen screws (1) .
- Feed out engine wiring harness (2)
of sensor system 1 and set aside.
- Unlock and disconnect plug connections (1) .
- Release the clamps (arrows).
- Feed out engine wiring harness (2)
of sensor system 1 and set aside.
- Unlock plug connection (1) and disconnect.
- Release the clamps (arrows).
- Feed out engine wiring harness (2)
of sensor system 1 and set aside.
- Feed out engine wiring harness (1) for sensor system 1 and remove it.