Installing the turbocharger for the cylinders 1 to 4
WARNING:
Hot surfaces
.
Risk of burning!
Risk of burning!
- Perform all work only on components that have cooled down.
CAUTION:
Heavy component
.
Heavy components can lead to injury or damage .
Heavy components can lead to injury or damage .
- Remove and install heavy components with the aid of another person/other persons.
NOTE:
RISK OF DAMAGE
Contaminant or foreign body .
Contamination can result in malfunctions, loss of function or leaks .
Contaminant or foreign body .
Contamination can result in malfunctions, loss of function or leaks .
- Adhere to the utmost cleanliness.
- Protect components from contamination e.g. by covering.
- Close off line connections with seal plugs.
NOTE:
TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents.
The sealing surfaces must be free of oil, grease and cleaning agents.
Prepare for the installation of the turbocharger
- Check the oil feed lines and oil return lines for contamination or obstruction, clean or replace if necessary.
- If the oil feed lines or oil return lines are heavily contaminated, it is recommended that the engine oil and oil filter are changed.
- If installed: Check the coolant feed lines and coolant return lines for the turbocharger for contamination or obstruction and clean or replace as needed.
- Check the screw connections and plug connections of all lines for accuracy.
- Check air cleaner for contamination and clean or replace as needed.
- Check correct functioning of crankcase ventilation.
- Replace all gaskets.
Parts: Seals
- Replace the seal (1).
Parts: Seal
- Check the pin (arrow) for damage, replace exhaust manifold if necessary.
- Make sure that the O-ring (1) does not fall into the oil duct in the engine block.
- Replace O-ring (1).
Parts: O-ring
If the O-ring (1) cannot be disassembled, the oil return lid must be disassembled.
- Coat O-ring (1) with engine oil.ENGINE OIL SPECIFICATION
Technically suitable engine oils for BMW Group engines - Loosen screws (2).
- Remove the oil return line (1).
- Ensure that the sealing surfaces in the area of the oil return line are planar and free from oil and grease.
- Replace oil return line (3) after each disassembly of the turbocharger.
Parts: Oil return line
- Replace the seal (1).
Parts: Seal
- Replace screws (2).
Parts: Screws
- Position screws (2) in oil return line (3).
- Position the seal (1) on the screws (2).
- Position the oil return line (1).
- Screws (2) must be tightened with the aid of an support person.TIGHTENING TORQUES SPECIFICATION
Oil return line at the exhaust turbocharger M6x16
Replace screws.Joining torque 5 Nm Angle of rotation 60° - Feed in and install the turbocharger (2) at right with the coolant lines and oil return line.
- When installing the right turbocharger (2), make sure that the oil return line is correctly positioned in the oil return cover.
- Make sure the oil feed line (1) is positioned correctly.
- Insert the holder (3).
- Tighten down screws (1).TIGHTENING TORQUES SPECIFICATION
Holder of sensor system M6x16 screw tightening torque 8 Nm - Connect connectors (1) and lock.
- Secure the wiring harness mounting (1).
- Secure cables (3) in the bracket (2).
- Replace V-band clamp (2).
Parts: V-band clamp
- Position V-clip (2).
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Exhaust turbocharger to exhaust manifold V-band clamp
Replace V-band clamp.Tightening torque 20 Nm - Tighten the screw (1) on the oil return pipe (2).TIGHTENING TORQUES SPECIFICATION
Oil return line to oil return cover M6 tightening torque 10 Nm - Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Replace sealing ring (1) of the coolant line (2).
Parts: Sealing ring
- Connect coolant lines (4).
- Connect coolant lines (3).
- Tighten down screws (2).TIGHTENING TORQUES SPECIFICATION
Coolant line from exhaust turbocharger to bracket M6x30 tightening torque 8 Nm - Remove the lint-free rag (1).
- Connect connectors (1) and lock.
- Replace the screw (1).
Parts: Screw
- Replace the sealing ring or sealing rings (2).
Parts: Sealing ring or sealing rings
- Make sure that when installing sealing rings without a fitting aid (bridge), both sealing rings are replaced.
- Position screw (1) with the sealing ring or sealing rings (2) on the oil feed line.
- Determining the screw type and selecting the appropriate socket wrench:
Screw type Matching socket wrench Hexagon screw (3) Commercial socket wrench (1) Multi-tooth screw (4) Multi-tooth socket wrench (2) - Position oil feed line.
- Screw in the banjo bolt (2) several threads.
- Hand-tighten the bolt (1).
- Tighten the banjo bolt (2).TIGHTENING TORQUES SPECIFICATION
Banjo bolt for oil feed line to exhaust turbocharger M10x1
Replace the screw and sealing rings.Joining torque 8 Nm Angle of rotation 70° - Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Oil feed line to exhaust turbocharger | ||
|---|---|---|
| M6x16 | tightening torque | 10 Nm |
Follow-up work
- Refer to INSTALLING THE INTAKE PIPE OF THE ENGINE VENTILATION LINE .
- Refer to INSTALLING RIGHT CLEAN AIR PIPE .
- Refer to PARTIALLY INSTALLING THE RIGHT ENGINE VENTILATION LINE .
- Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE TURBOCHARGER .
- Refer to INSTALLING THE CARRIER PLATE .
- Refer to INSTALLING THE CATALYTIC CONVERTER OF CYLINDERS 1 TO 4 .
- Refer to INSTALLING THE RIGHT OXYGEN SENSOR MONITOR .
- Refer to INSTALLING HEAT SHIELD, TOP .
- Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
- Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
- Refer to INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
- Refer to INSTALLING THE REAR LEFT AND RIGHT TENSION STRUT .
- Refer to INSTALLING THE LEFT AND RIGHT UNDERSHIELD (TANK COVER) .
- Refer to CONNECTING THE COOLANT HOSES TO THE HIGH-TEMPERATURE COOLANT RADIATOR .
- Refer to INSTALLING FAN COWL .
- Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
- Refer to INSTALLING THE RIGHT AND LEFT UNFILTERED-AIR DUCT .
- Refer to INSTALLING BOTH INTAKE FILTER HOUSING .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
- Refer to INSTALLING UPPER CROSS CONNECTION .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .