Vent the high-temperature coolant system
WARNING: This page is about a different car, the 2023 BMW X5, 2022 BMW X5, 2021 BMW X5, 2020 BMW X5, and 2019 BMW X5. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
TECHNICAL INFORMATION
Immobilization period-long fill of coolant!
Do not reuse used coolant.
When replacing and removing components which rely on the corrosion protection effect of the coolant, it is essential to change the coolant. The cooling system must therefore be emptied and refilled.
In the case of other removal work involving the draining of part quantities of coolant, the coolant level must be topped up with new coolant.
Immobilization period-long fill of coolant!
Do not reuse used coolant.
When replacing and removing components which rely on the corrosion protection effect of the coolant, it is essential to change the coolant. The cooling system must therefore be emptied and refilled.
In the case of other removal work involving the draining of part quantities of coolant, the coolant level must be topped up with new coolant.
NOTE:
TECHNICAL INFORMATION
Filling without the vacuum filling equipment (watering can filling) is not permitted .
If this is not observed, there is a risk of component damage or engine damage. The filling specification must be observed.
It is essential to visually check the vacuum filling equipment before use to check that it is functioning correctly and clean.
It is not permissible to operate the vehicle if the filling procedure has not been fully completed. Otherwise there may be functional limitations (degradation) or overheating.
A bleeding procedure is required after a part has been exchanged in the cooling system and/or after refilling the cooling system.
Filling without the vacuum filling equipment (watering can filling) is not permitted .
If this is not observed, there is a risk of component damage or engine damage. The filling specification must be observed.
It is essential to visually check the vacuum filling equipment before use to check that it is functioning correctly and clean.
It is not permissible to operate the vehicle if the filling procedure has not been fully completed. Otherwise there may be functional limitations (degradation) or overheating.
A bleeding procedure is required after a part has been exchanged in the cooling system and/or after refilling the cooling system.
NOTE:
TECHNICAL INFORMATION
Before starting the automatic cooling system bleeding procedure, make sure that all coolant circuits are filled . If the cooling system bleeding procedure is started while one of the coolant circuits is empty, there is a risk of damage to the electric coolant pump when running it dry.
Make sure that terminal 15 is not disconnected for the bleeding procedure . Switch on low-beam headlights and hazard warning lights. If the low-beam headlights and hazard warning lights are not switched on, the ignition (terminal 15) will switch off automatically after a certain period of time and interrupt the bleeding procedure.
Before starting the automatic cooling system bleeding procedure, make sure that all coolant circuits are filled . If the cooling system bleeding procedure is started while one of the coolant circuits is empty, there is a risk of damage to the electric coolant pump when running it dry.
Make sure that terminal 15 is not disconnected for the bleeding procedure . Switch on low-beam headlights and hazard warning lights. If the low-beam headlights and hazard warning lights are not switched on, the ignition (terminal 15) will switch off automatically after a certain period of time and interrupt the bleeding procedure.
NOTE:
TECHNICAL INFORMATION
G07 with S4NNA: The air conditioning control panel must be switched off.
G07 with S4NNA: The air conditioning control panel must be switched off.
NOTE:
TECHNICAL INFORMATION
The electrical fan is activated during the entire cooling system bleeding procedure.
The electrical fan is activated during the entire cooling system bleeding procedure.
NOTE:
TECHNICAL INFORMATION
The driving dynamics control must not be set to the ECO PRO switch position.
The driving dynamics control must not be set to the ECO PRO switch position.
- Adjust the coolant level in the high temperature coolant expansion tank (1) to the lower edge (2) of the coolant filler neck of the high temperature coolant expansion tank (1).
- Close the sealing cap on the coolant expansion tank of the high-temperature cooling circuit.
- Ensure that the hood is closed .
- Make sure that all the wheels have ground contact.
- Engage the parking brake.
- On a manual transmission, do not engage a gear, and on an automatic transmission, put it in "P" or "N".
- Connect battery charger.
- Activate testing-analysis-diagnosis (PAD) by quickly pressing the START-STOP button three times.
- Activate the low beams and the hazard-warning lights at the same time .
If the low beams and the hazard-warning lights are not turned on, the ignition (terminal 15 ) turns off automatically after a while and interrupts the bleeding procedure.
- Ensure that Driving Dynamics Control is not in the "ECO PRO" switch position.
- G07 with S4NNA : 3rd seat row must be locked (seat not folded down)
- Set the heating to the maximum temperature and the blower to the lowest level.
- G07 with S4NNA : Set the rear heating to maximum temperature ("HIGH") via Sync mode.
- Press the accelerator pedal up to the stop for at least 10 s and do not press the brake pedal while doing this.
- Start engine.
- The cooling system bleeding procedure starts, note the display on the instrument cluster (KOMBI). ("service function started")
The engine speed (up to 3500 rpm) and the actuators in the engine cooling system are activated automatically according to a cooling system bleeding procedure for 11 min.
The cooling system bleeding procedure ends approx. 11 min after the engine start.
The engine speed reduces to idle speed.
- Note the display on the instrument cluster (KOMBI) ("Service function ended").
If the service function is canceled, the cooling system bleeding procedure must be repeated ("Service function canceled").
- G07 with S4NNA : Run the engine at idling speed for about 5 min.. Set the heating to maximum temperature ("HIGH") via Sync mode.
- Switch off engine.
- Let the coolant temperature cool down to < 50°C .
- Loosen sealing cap (1).
NOTE:
TECHNICAL INFORMATION
After the cooling system bleeding procedure, the cooling system is topped up via the maximum mark.
Overfilling the cooling system serves to balance the remaining air in the cooling system. The normal fill level of the coolant is reached during driving.
After the cooling system bleeding procedure, the cooling system is topped up via the maximum mark.
Overfilling the cooling system serves to balance the remaining air in the cooling system. The normal fill level of the coolant is reached during driving.
- Adjust fill level in coolant expansion tank of high-temperature coolant circuit to 200 ml over maximum mark .
- Close sealing cap (1).
- Close the sealing cap (1) until the arrows align.