51 47 Floor-Trunk-Engine Compartment-Trim Panel
FLOOR-TRUNK-ENGINE COMPARTMENT-TRIM PANEL - 5147 TIGHTENING TORQUE OVERVIEW
| Automated slide & anti-slip rail to luggage compartment floor covering | ||
| screw | Tightening torque | 2 Nm |
| Cover to side member | ||
| Oval-head screw | Tightening torque | 8.0 Nm |
| Cover to side member | ||
| Screw TS5x16 | tightening torque | 3.0 Nm |
| Plastic nut | tightening torque | 3.0 Nm |
| Cross member holder on body | ||
| Screw M 10x18 | tightening torque | 12 Nm |
| Plastic nut | tightening torque | 2.6 Nm |
| Door sill cover strip to body | ||
| Screw 4.8x16 | Tightening torque | 1.4 Nm |
| Drive for cover flap of electrical roller cover for luggage compartment to luggage compartment floor covering | ||
| screw | Tightening torque | 1.2 Nm |
| Drive on body | ||
| Nut | Tightening torque | 9.5 Nm |
| Drive unit to holder | ||
| M5 nut | Tightening torque | 5.5 Nm |
| Guide pins to roller cover for luggage compartment | ||
| Screw | Tightening torque | 1.0 Nm |
| Holder for roller cover for luggage compartment on body | ||
| M 8x20 screws | Tightening torque | 8.5 Nm |
| Holder for roller cover for luggage compartment on rear of body | ||
| Screws TS5x16 | Tightening torque | 3.0 Nm |
| Loading edge trim to body | ||
| Screw | tightening torque | 3.0 Nm |
| Luggage compartment floor covering on holder | ||
| Oval-head screw | Tightening torque | 15 Nm |
| Luggage compartment trim panel to body | ||
| Oval-head screw TS5x16 | tightening torque | 3.0 Nm |
| Hexagon screw M6x12 | tightening torque | 4.0 Nm |
| Luggage compartment trim panel to body | ||
| Oval-head screw M5x16 | Tightening torque | 3.0 Nm |
| hexagon screw M4.8x19 | Tightening torque | 3.0 Nm |
| Plastic nut | Tightening torque | 2.6 Nm |
| Luggage compartment wheel arch trim panel on body | ||
| screw | Tightening torque | 3.0 Nm |
| Protective plate to door | ||
| Screw M8x25 | tightening torque | 35 Nm |
| Protective plate to holder | ||
| Nut M8 | tightening torque | 10 Nm |
| Flat-head screw M8x22 | tightening torque | 35 Nm |
| Removing drive for the automated skid and non-slip rail on the luggage compartment floor covering | ||
| Screw | tightening torque | 2 Nm |
| Roller cover for luggage compartment to drive unit | ||
| screw | Tightening torque | 2.0 Nm |
| Safety partition wall at the center to the holder | ||
| Hexagon screw M8x25 | tightening torque | 35 Nm |
| Safety partition wall at the center to the safety partition below | ||
| Hexagon screw M8x30 | tightening torque | 35 Nm |
| Nut M8 | tightening torque | 10 Nm |
| Shelf on body | ||
| Plastic nut | Tightening torque | 3 Nm |
| Side member cover to bodyshell | ||
| screw | Tightening torque | 3 Nm |