Installing the crankshaft

Rotate the threaded support sleeves in reverse 

• Rotate the threaded support sleeves in the main bearing cap in reverse.

Courtesy of BMW OF NORTH AMERICA, INC.

When replacing the crankshaft bearings or crankshaft 

Replacement: Observing the classification of bearing shells 

• Observe the classification of the bearing shells (1) through (3):

  The bearing shell (1) has yellow color coding in the (5) area.

  The bearing shell (2) has green color coding in the (5) area.

  The bearing shell (3) has purple color coding in the (5) area.

• Make sure that the right classification is implemented in accordance with the (4) area.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the main bearing shells.

  Parts:  Main bearing shells

Courtesy of BMW OF NORTH AMERICA, INC.

• Observe the assignment of classification of bearing seats (1) to (5) on the crankshaft:

• Observe the assignment of classification of bearing seats (1) to (5) on the crankcase upper section:

Courtesy of BMW OF NORTH AMERICA, INC.

Check 

• Read the code letters and code numbers of crankcase (1) and crankshaft (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Result 

» Note the result in the table.

Measure

• Determine classification of the bearing shells based on further information: Table for bearing shells of bearing seat.

TABLE FOR BEARING SHELLS OF BEARING SHELLS N63

• Insert the bearing shells in bearing seats (1), (2), (4) and (5).
• Insert bearing shell (3) in the guide bearing seat on the crankcase.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Insert the bearing shells in bearing caps (1), (2), (4) and (5).
• Insert bearing shell (3) into the guide bearing cap.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install crankshaft.
• Position all main bearing caps with bearing shells.
• Observe the assignment of the crankshaft bearing caps from (1) to (5).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace screws.

  Parts:  Screws

• Fasten the collar screws (M11) in the order (1) to (10).
  Fig 1: Main Bearing Cap Collar Screws Tightening Sequence (M11)

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace screws.

  Parts:  Screws

• Fasten the collar screws (M8) in the order (1) to (10).

Fig 2: Main Bearing Cap Collar Screws Tightening Sequence (M8)

Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten all threaded support bushings (1).

Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten the main bearing transverse screws on the spacer bolts (1), the screws (2), and the spacer screw (3).

Courtesy of BMW OF NORTH AMERICA, INC.

• Screw central bolt (1) into the crankshaft by hand.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Check the coefficient of friction at the crankshaft.
• Determine the crankshaft breakaway torque with the special tool 0 490 130 (00 2 010)  .
• Turn the crankshaft on the central bolt with the special tool.

Courtesy of BMW OF NORTH AMERICA, INC.

• Correct the main bearing clearance in case the breakaway torque is too high.
• Unscrew the central bolt (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure special tool with magnetic foot on crankcase.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Set the torque wrench (1) to 20 Nm.
• Attach the special tool 2 446 957  to the torque wrench.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Set dial gauge to zero.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Slide the crankshaft to the front in the arrow direction up to the stop at 20 Nm.
• Observe the deflection of the dial gauge  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Slide the crankshaft to the rear in the arrow direction up to the stop at 20 Nm.
• Observe the deflection of the dial gauge  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Compare the side clearance of the crankshaft to the setpoint value and assess.

• Remove the special tool.

Courtesy of BMW OF NORTH AMERICA, INC.

Install the tensioning rail of the timing chain for cylinder 5-8 

• Position the tensioning rail (1) with the timing chain (2) on the gearing of the crankshaft.

  Courtesy of BMW OF NORTH AMERICA, INC.

  Install the guide rail of the timing chain for cylinders 5 to 8 

• Attach and position the slide rail (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  Install the tensioning rail of the timing chain for cylinder 1-4 

• Position the tensioning rail (1) with timing chain on the gearing of the crankshaft.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Attach and position the slide rail (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  Mounting the beaded metal gaskets 

• Clean sealing surfaces (2).
• Replace beaded metal gaskets (1).

  Parts:  Sheet metal beaded seals

• Securing the beaded metal gaskets (1) with the timing case cover screws.
• For timing case cover or timing chain replacement: 

  Loosen screw (3).

  Remove jump guard (4).

  Position jump guard (4).

  Tighten down screw (3).

Courtesy of BMW OF NORTH AMERICA, INC.

• For timing case cover or timing chain replacement: 

  Release and remount coolant temperature sensor (1).

  Tighten the coolant temperature sensor (1).

Courtesy of BMW OF NORTH AMERICA, INC.

• The centering pins (1) must not be damaged, replace if necessary.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Clean sealing surfaces (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

  Tightening the screw connection 1 on the front timing case cover 

• Position the timing case cover.
• Tighten screws in the order (1) to (2).

Fig 3: Timing Case Cover Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Securing the screw connection 2 on the front timing case cover 

• Tighten screws in the order (3) to (9).

Fig 4: Front Timing Case Cover Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Mounting the screw connection 3 on the front timing case cover 

• Position the carrier plate (1).
• Tighten screws in the order (10) to (12).

Fig 5: Carrier Plate Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the plug connection (1) to the coolant temperature sensor (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Install the roller chain (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Installing the sealing cap with radial shaft seal (oil pan removed) 

• Clean sealing surface (1).

  Courtesy of BMW OF NORTH AMERICA, INC.

• The sealing cap with radial shaft seal (1) must not be stored longer than 6 months without support bushing (2).
• The support bushing (2) must remain in the sealing cap with radial shaft seal (1) until installation as it is used as a slip bushing.

Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the sealing cap with radial shaft seal (1).

  Parts:  Sealing cap with radial shaft seal

• Coat the tire tread of the crankshaft with motor oil.

Courtesy of BMW OF NORTH AMERICA, INC.

Engine oil 

Technically suitable engine oils for BMW Group engines 

• Position and slide on the sealing cap with the radial shaft seal (1) and the support bushing (2) on the crankshaft.
• Abut screws (1).
• Tighten down screws (2).
• Tighten down screws (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING PISTON WITH CONNECTING ROD .
• Refer to INSTALLING THE UPPER OIL SUMP SECTION .
• Refer to INSTALLING THE VIBRATION DAMPER .
• Refer to INSTALLING FRONT AXLE DIFFERENTIAL .
• Refer to INSTALLING OIL PUMP .
• Refer to INSTALLING THE LOWER OIL PAN SECTION .
• Refer to INSTALLING THE RIGHT CYLINDER HEAD .
• Refer to INSTALLING BOTH RIGHT VANOS ADJUSTERS .
• Refer to REMOVING THE SPECIAL TOOL TO PRETENSION THE TIMING CHAIN AT CYLINDER BANK 1 .
• Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 1 .
• Refer to INSTALLING THE SEALING CAP ON THE CYLINDER HEAD OF CYLINDER BANK 1 .
• Refer to INSTALLING THE CYLINDER HEAD COVER ON THE RIGHT .
• Refer to INSTALLING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 1 .
• Refer to INSTALLING THE VANOS SOLENOID ACTUATOR INTAKE OF CYLINDER BANK 1 .
• Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 1 TO 4 .
• Refer to SECURING THE WIRING HARNESS SECTION OF THE CYLINDER HEAD COVER ON THE RIGHT .
• Refer to INSTALLING RIGHT HIGH PRESSURE PUMP .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to INSTALLING THE RIGHT HIGH-PRESSURE RAIL .
• Refer to INSTALLING THE GUIDE TUBE FOR THE OIL DIPSTICK .
• Refer to INSTALLING THE OIL FILLER CAP .
• Refer to INSTALLING IGNITION COILS OF CYLINDER BANK 1 .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDERS 1 TO 4 .
• Refer to INSTALLING THE LEFT CYLINDER HEAD .
• Refer to INSTALLING BOTH LEFT VANOS ADJUSTERS .
• Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN ON CYLINDER BANK 2 .
• Refer to INSTALLING THE HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 2 .
• Refer to INSTALLING THE SEALING CAP ON THE CYLINDER HEAD OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT CYLINDER HEAD COVER .
• Refer to INSTALLING THE VANOS SOLENOID ACTUATOR EXHAUST OF CYLINDER BANK 2 .
• Refer to INSTALLING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to SECURING THE WIRING HARNESS SECTION FROM THE CYLINDER HEAD COVER ON THE LEFT .
• Refer to INSERTING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE ENGINE VENTILATION LINE OF CYLINDERS 5 TO 8 .
• Refer to INSTALLING THE INTAKE PIPE OF THE ENGINE VENTILATION LINE .
• Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
• Refer to INSTALLING THE BELT TENSIONER .
• Refer to INSTALLING COOLANT PUMPS .
• Refer to INSTALLING RIGHT CLEAN AIR PIPE .
• Refer to INSTALLING LEFT CLEAN AIR PIPE .
• Refer to INSTALLING THE LEFT ENGINE VENTILATION LINE (PARTIALLY REMOVED) .
• Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
• Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
• Refer to CONNECTING THE LEFT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to CONNECTING THE RIGHT CHARGE AIR LINE TO THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE CARRIER PLATE .
• Refer to PREPARING THE INJECTORS FOR INSTALLATION .
• Refer to INSTALLING THE INJECTORS FOR THE CYLINDERS 5 TO 8 .
• Refer to CONNECTING THE CONNECTOR OF THE INJECTORS OF CYLINDER BANK 2 .
• Refer to INSTALLING THE LEFT HIGH PRESSURE PUMP .
• Refer to INSTALLING THE HIGH-PRESSURE RAIL ON THE LEFT .
• Refer to INSTALLING THE SOUND INSULATION OF THE INJECTORS, LEFT .
• Refer to INSTALLING THE IGNITION COILS OF CYLINDER BANK 2 .
• Refer to INSTALLING IGNITION COIL ON CYLINDER 1 .
• Refer to INSTALLING AIR CONDITIONING COMPRESSOR (ENGINE REMOVED) .
• Refer to INSTALLING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
• Refer to INSTALLING THE BELT TENSIONER .
• Refer to INSTALLING DRIVE BELT .
• Refer to INSTALLING THE FLYWHEEL .
• Refer to REMOVING THE ENGINE FROM THE ENGINE SUPPORT BRACKET .
• Refer to INSTALLING THE COMPLETE FRONT AXLE WITH THE ENGINE AND TRANSMISSION .
• Refer to INSTALLING THE OIL FILTER ELEMENT .
• Refer to TIGHTENING THE OIL DRAIN PLUG .
• Refer to FILLING ENGINE OIL .