Removing crankshaft

WARNING: Working on fuel system .
Risk of fire! Danger of explosion!

When working on the fuel system, make sure the workstation has sufficient ventilation, e.g., by means of extraction.
Tightly seal off open lines and connections; collect any leakage fuel directly at the point of exit.

No fire, sparks, open flames or smoking.

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

Preliminary work

Refer to RELEASING THE OIL DRAINING PLUG .
Refer to REMOVING THE OIL FILTER ELEMENT .
Refer to REMOVING THE FRONT AXLE COMPLETELY WITH THE ENGINE AND TRANSMISSION .
Refer to INSTALLING THE ENGINE ON THE ASSEMBLY JIG .
Refer to REMOVING FLYWHEEL .
Refer to REMOVING IGNITION COILS FROM THE CYLINDER BANK 2 .
Refer to REMOVING IGNITION COILS FROM CYLINDER BANK 1 .
Refer to REMOVING THE SOUND INSULATION OF INJECTORS ON LEFT .
Refer to REMOVING THE HIGH-PRESSURE RAIL ON THE LEFT .
Refer to REMOVING LEFT HIGH PRESSURE PUMP .
Refer to DISCONNECTING PLUG CONNECTIONS OF THE INJECTORS OF CYLINDER BANK 2 .
Refer to REMOVING THE INJECTORS FOR CYLINDERS 5 TO 8 .
Refer to REMOVING CARRIER PLATE .
Refer to RELEASING LEFT CHARGE AIR LINE PARTIALLY .
Refer to PARTIALLY RELEASING THE RIGHT CHARGE AIR LINE .
Refer to REMOVING LEFT CHARGE AIR COOLER .
Refer to REMOVING RIGHT CHARGE AIR COOLER .
Refer to REMOVING THE INTAKE PIPE THE ENGINE VENTILATION LINE .
Refer to REMOVING ENGINE VENTING LINE OF CYLINDERS 1 TO 4 .
Refer to REMOVING ENGINE VENTING LINE OF CYLINDERS 5 TO 8 .
Refer to REMOVING LEFT CLEANING AIR PIPE .
Refer to REMOVING RIGHT CLEANING AIR PIPE .
Refer to REMOVING DRIVE BELT .
Refer to REMOVING THE COOLANT PUMP .
Refer to REMOVING THE BELT TENSIONER .
Refer to REMOVING THE BELT PULLEY ON THE TORSIONAL VIBRATION DAMPER .
Refer to REMOVING THE AIR CONDITIONING COMPRESSOR (ENGINE REMOVED) .
Refer to REMOVING THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
Refer to RELEASING THE WIRING HARNESS SECTION FROM THE LEFT HAND CYLINDER HEAD COVER .
Refer to REMOVING FUEL DELIVERY LINE .
Refer to REMOVING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 2 .
Refer to REMOVING VANOS SOLENOID ACTUATOR, INTAKE OF CYLINDER BANK 2 .
Refer to REMOVING LEFT CYLINDER HEAD COVER .
Refer to REMOVING THE SEALING CAP ON THE CYLINDER HEAD OF THE CYLINDER BANK 2 .
Refer to MOVING THE CRANKSHAFT TO THE INSTALLATION POSITION TO ADJUSTING THE TIMINGS .
Refer to CHECKING THE VANOS ADJUSTER OF CYLINDER BANK 2 .
Refer to RELAXING CHAIN TENSIONER ON BANK 2 FOR CHECKING OR SETTING TIMING .
Refer to REMOVING HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 2 .
Refer to PRELOADING THE TIMING CHAIN OF CYLINDER BANK 2 .
Refer to FIXING THE ENGINE IN THE INSTALLATION POSITION ON CYLINDER 1 (SET VALVE TIMINGS) .
Refer to REMOVING BOTH LEFT VANOS ADJUSTERS .
Refer to REMOVING SPECIAL TOOL FOR FIXING CAMSHAFTS IN POSITION ON BANK 2 .
Refer to REMOVING SPECIAL TOOL TO PRETENSION TIMING CHAIN ON CYLINDER BANK 2 .
Refer to REMOVING LEFT CYLINDER HEAD .
Refer to REMOVING GUIDE TUBE FOR OIL DIPSTICK .
Refer to REMOVING RIGHT RAIL .
Refer to REMOVING RIGHT HIGH-PRESSURE PUMP .
Refer to PARTIALLY RELEASING THE WIRING HARNESS SECTION OF THE RIGHT CYLINDER HEAD COVER .
Refer to REMOVING THE INJECTORS FOR CYLINDERS 1 TO 4 .
Refer to REMOVING VANOS SOLENOID ACTUATOR, EXHAUST OF CYLINDER BANK 1 .
Refer to REMOVING THE VANOS SOLENOID ACTUATOR INTAKE OF CYLINDER BANK 1 .
Refer to REMOVING RIGHT CYLINDER HEAD COVER .
Refer to REMOVING THE SEALING CAP ON THE CYLINDER HEAD OF THE CYLINDER BANK 1 .
Refer to MOVING THE CRANKSHAFT TO THE INSTALLATION POSITION TO ADJUSTING THE TIMINGS .
Refer to CHECKING THE VANOS ADJUSTER OF CYLINDER BANK 1 .
Refer to RELIEVING THE CHAIN TENSIONER AT CYLINDER BANK 1 FOR CHECKING OR SETTING THE VALVE TIMINGS .
Refer to REMOVING HYDRAULIC CHAIN TENSIONER OF CYLINDER BANK 1 .
Refer to PRELOADING THE TIMING CHAIN OF CYLINDER BANK 1 .
Refer to FIXING THE ENGINE IN THE INSTALLATION POSITION ON CYLINDER 1 (SET VALVE TIMINGS) .
Refer to REMOVING BOTH RIGHT VANOS ADJUSTERS .
Refer to REMOVING SPECIAL TOOL FOR FIXING CAMSHAFTS ON BANK 1 .
Refer to REMOVING THE SPECIAL TOOL TO PRETENSION THE TIMING CHAIN AT CYLINDER BANK 1 .
Refer to REMOVING RIGHT CYLINDER HEAD .
Refer to REMOVING LOWER OIL PAN SECTION .
Refer to REMOVING OIL PUMP .
Refer to REMOVING FRONT AXLE DIFFERENTIAL .
Refer to REMOVING THE VIBRATION DAMPER .
Refer to REMOVING UPPER OIL SUMP SECTION .
Refer to REMOVING THE PISTON WITH CONNECTING ROD .

Removing sealing cap with radial shaft seal (oil pan removed)

Loosen screws (1).
Loosen screws (2).

Remove the sealing cap with radial shaft seal (3).

Courtesy of BMW OF NORTH AMERICA, INC.

Remove the roller chain (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock and disconnect the plug connection (1) on the coolant temperature sensor (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Unscrew the screw connection 1 on the timing case cover in front

Loosen screws in the order (10) to (12).
Remove the carrier plate (1).

Fig 1: Carrier Plate Screws Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Release the screw connection 2 on the front timing case cover

Loosen screws in the order (9) to (3).

Fig 2: Timing Case Cover Screws Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Release the screw connection 3 on the timing case cover in front

Loosen screws in the order (1) to (2).
Remove timing case cover.

Fig 3: Timing Case Cover Screws Loosening Sequence - Front

Courtesy of BMW OF NORTH AMERICA, INC.

Remove the slide rail (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Remove the tensioning rail of the timing chain for cylinder 1-4

Remove the tensioning rail (1) with the timing chain (2) from the crankshaft gearing.

Courtesy of BMW OF NORTH AMERICA, INC.

Removing the slide rail of the timing chain for cylinders 5 to 8

Remove the slide rail (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Remove the tensioning rail of the timing chain for cylinder 5-8

Remove the tensioning rail (1) with the timing chain (2) from the crankshaft gearing.

Courtesy of BMW OF NORTH AMERICA, INC.

Observe the arrangement of the main bearing cap as well as the assignment of the crankshaft bearing caps from (1) to (5).

Courtesy of BMW OF NORTH AMERICA, INC.

Loosen the main bearing transverse screws on the spacer bolts (1), the screws (2), and the spacer screw (3).

Courtesy of BMW OF NORTH AMERICA, INC.

Unscrew all threaded bushing sleeves (1).

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: The operations shown only for one side must be carried out on both sides.

Loosen screws (1).
Release the collar screws (M8) in the sequence (10) to (1).

Fig 4: Bearing Cap Collar Screws Loosening Sequence (M8)

Courtesy of BMW OF NORTH AMERICA, INC.

Release the collar screws (M11) in the sequence (10) to (1).
Remove the main bearing cap.

CAUTION: Component with heavy weight .
Injury hazard!

Note component's center of gravity.
Support component using a jack.

Secure component against falling off the jack.

Fig 5: Bearing Cap Collar Screws Loosening Sequence (M11)

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The work must be performed with vehicle care to prevent component damage.

Remove the crankshaft with a support person (weight approx. 25 kg).
Lift out crankshaft and set down safely (secure against turning).