Install exhaust camshaft

Clean all the bearing positions (arrows).
Coat all bearing positions (arrows) with motor oil.

Courtesy of BMW OF NORTH AMERICA, INC.
Clean all bearing positions of the exhaust camshaft bearing caps (A1), (A2), (A3), (A4) and (A) and coat with motor oil.
Clean the bearing positions (1) of the high pressure pump bracket and coat with motor oil.

Courtesy of BMW OF NORTH AMERICA, INC.
Clean all the bearing positions (arrows) of the exhaust camshaft.
Coat all bearing positions (arrows) of the exhaust camshaft with motor oil.

Courtesy of BMW OF NORTH AMERICA, INC.
Check all roller cam follower (1) of the exhaust side for correct fit.

Courtesy of BMW OF NORTH AMERICA, INC.
Insert the exhaust camshaft (2) in the cylinder head, so that the mark (1) points upwards.

Courtesy of BMW OF NORTH AMERICA, INC.
Check the fitting sleeves (1) of the thrust bearing for damage, replace if necessary.
Check the fitting sleeves (2) of the high pressure pump bracket for damage, replace if necessary.

Courtesy of BMW OF NORTH AMERICA, INC.
NOTE:
RISK OF DAMAGE
Engine damage caused by incorrectly installed bearing shells and bearing brackets .
If the bearing shells and bearing brackets are installed incorrectly, then engine damage can occur .
- Always install all bearing shells and bearing brackets in the same position from which they were removed.
Courtesy of BMW OF NORTH AMERICA, INC.
Replace all exhaust camshaft bearing cap so that the labeling (1) from the intake side are readable.
NOTE: TECHNICAL INFORMATION
The camshaft bearing caps must not be mixed up. The camshaft bearing caps must be installed in the installation position from which they were removed.
Oil all the exhaust camshaft bearing caps (A1) to (A4) and the exhaust camshaft bearing cap for the thrust bearing (A) with motor oil and place into position.

Courtesy of BMW OF NORTH AMERICA, INC.
Oil the bearing position at the high pressure pump bracket with motor oil and place the high pressure pump bracket into position.
Check the tensile strength of the screws for the bearing caps.
The illustration shows the screw with a tensile strength of 8.8 .

Courtesy of BMW OF NORTH AMERICA, INC.
Check the tensile strength of the screws for the bearing cap.
The illustration shows the screw with a tensile strength of 10.9 .

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The camshaft is under tension due to the valve springs. Tighten or loosen each screw on the camshaft bearing caps in the prescribed sequence only by half a turn. Repeat procedure.
Press the exhaust camshaft bearing cap down and hand-tighten the screws incrementally in sequence (1) to (14).

Fig 1: Exhaust Camshaft Bearing Cap Screws Tightening Sequence
Courtesy of BMW OF NORTH AMERICA, INC.
Abut all screws in the sequence from (1) to (14) in half turns .
Observe the joining torque .

Tighten all screws in a sequence from (1) to (14).

TIGHTENING TORQUE SPECIFICATIONS

Exhaust camshaft to cylinder head
M6 Tensile strength of screw 8.8	Joining torque	9.6 Nm
M6 Tensile strength of screw 8.8	tightening torque	9.6 Nm
M6 Tensile strength of screw 10.9	Joining torque	11.8 Nm
M6 Tensile strength of screw 10.9	tightening torque	11.8 Nm

Relax special tool 2 410 670 above the spindle nut.
Release special tools 0 495 741 (11 8 552) and remove the special tool 2 410 670 .

Courtesy of BMW OF NORTH AMERICA, INC.
Position and install the roller tappet (1).
Make sure the pin (2) is correctly positioned in the guide (3).
Insert and install the roller tappet (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to ADJUSTING THE CAMSHAFTS WITH THE SPECIAL TOOL .
Refer to INSTALLING EXHAUST CAMSHAFT ADJUSTER .
Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to RELEASING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to INSTALLING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to PRE-TENSIONING THE TIMING CHAIN WITH THE SPECIAL TOOL .
Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE EXHAUST CAMSHAFT ADJUSTER .
Refer to TIGHTENING THE VANOS CENTRAL VALVE OF THE INTAKE ADJUSTER .
Refer to DISASSEMBLING ALL SPECIAL TOOLS .
Refer to INSTALL CHAIN TENSIONER .
Refer to CHECKING THE TIMINGS OF THE CAMSHAFT .
Refer to INSTALLING CYLINDER HEAD COVER .
Refer to INSTALLING BOTH ACTUATORS .
Refer to PREPARING THE INJECTORS FOR INSTALLATION .
Refer to INSTALLING THE HIGH-PRESSURE RAIL WITH INJECTORS OF THE CYLINDERS 4 TO 6 .
Refer to INSTALLING RAIL WITH INJECTORS OF CYLINDERS 1 TO 3 .
Refer to INSTALLING HIGH PRESSURE PUMP .
Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE PUMP AND THE HIGH-PRESSURE RAIL .
Refer to INSTALLING FUEL DELIVERY LINE .
Refer to INSTALLING ALL SPARK PLUGS .
Refer to INSTALLING ALL IGNITION COILS .
Refer to INSTALLING THE HOLDER OF THE POSITIVE BATTERY CABLE .
Refer to INSTALLING THE CENTER STRUT BRACE MOUNT .
Refer to INSTALLING THE LOWER SECTION OF THE FRONT WALL .
Refer to INSTALLING ACOUSTIC COVER AT REAR .
Refer to INSTALLING THE CENTER COWL UPPER PART .
Refer to INSTALLING THE RIGHT COWL UPPER PART .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
Refer to INSTALLING THE STRUT BRACE ON THE LEFT AND RIGHT .
Refer to INSTALLING THE CLEAN AIR PIPE AND THE RESONATOR .
Refer to INSTALLING THE INTAKE FILTER HOUSING (TENSION STRUT REMOVED ON SHOCK TOWER) .
Refer to INSTALLING THE TENSION STRUT ON THE RIGHT SHOCK TOWER .
Refer to CONNECTING ALL BATTERY GROUND LEADS .
Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
Refer to INSTALLING ACOUSTIC COVER .
Refer to INSTALLING FRONT UNDERBODY PROTECTION .
Refer to INSTALLING THE STIFFENING PLATE .
Refer to TAKING HOOD OUT OF THE SERVICE POSITION .