Installing the catalytic converter for cylinders 5 through 8

WARNING: Hot exhaust system .
Risk of burning!

Any work must exclusively be carried out with an exhaust system that has cooled down.

NOTE: RISK OF DAMAGE
Damage to the gasoline particulate filter .
Forcibly removing, installing or dropping the gasoline particulate filter down will damage it .

Remove and install the gasoline particulate filter without damaging it and without applying external force.
Avoid impacts/knocks to the gasoline particulate filter (e.g. by tools, falling down, hard contact with base).

Loosen screws (1) to (3).
Remove screws (arrows).
Feed out and remove the thrust field (4) in the area (5) of the wheel arch trim panel.

Courtesy of BMW OF NORTH AMERICA, INC.

Partially releasing the catalytic converter for cylinders 5 to 8 at the bottom

WARNING: Hot exhaust system .
Risk of burning!

Any work must exclusively be carried out with an exhaust system that has cooled down.

Release the nuts (1) at the bottom on the catalytic converter for cylinders 1 to 4.
Loosen catalytic converter from holder.

Courtesy of BMW OF NORTH AMERICA, INC.
Release the nuts (1) at the bottom on the catalytic converter for cylinders 5 to 8.
Loosen catalytic converter from holder.

Courtesy of BMW OF NORTH AMERICA, INC.

Release bottom screw (1) heat shield.
Release the heat shield (2) from the lower heat shield.

Courtesy of BMW OF NORTH AMERICA, INC.
Release top screw (1) heat shield.
Release right heat shield (2) from the other heat shield.
Thread out and remove right heat shield (2) towards top.

Courtesy of BMW OF NORTH AMERICA, INC.
Release bottom screw (1) heat shield.
Release the heat shield (2) from the lower heat shield.

Courtesy of BMW OF NORTH AMERICA, INC.
Release top screw (1) heat shield.
Release left heat shield (2) from the other heat shields.
Feed out left heat shield (2) to the top and remove.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen circlip (1) and remove.
Loosen circlip (2) and remove.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Loosen screws (2).
Loosen screw (3).
Remove holder (4).

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Loosen screws (2).
Loosen screw (3).
Remove holder (4).

Courtesy of BMW OF NORTH AMERICA, INC.
Remove the catalytic converter (1) for the cylinders 1 to 4 in arrow direction.

Courtesy of BMW OF NORTH AMERICA, INC.
Unscrew and remove the catalytic converter (1) for the cylinders 1 to 4 in arrow direction.

Courtesy of BMW OF NORTH AMERICA, INC.
Remove the catalytic converter (1) for the cylinders 5 to 8 in arrow direction.

Courtesy of BMW OF NORTH AMERICA, INC.
Unscrew and remove the catalytic converter (1) for the cylinders 5 to 8 in arrow direction.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING THE LEFT OXYGEN SENSOR MONITOR .
Refer to REMOVING THE HOLDER FOR THE DME CONTROL UNIT ON THE LEFT .
Refer to INSTALLING THE DME CONTROL UNIT OF CYLINDERS 5 TO 8 .
Refer to INSTALLING COVER FOR THE LEFT DME CONTROL UNIT .
Refer to INSTALLING THE LEFT UNFILTERED-AIR DUCT .
Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
Refer to INSTALLING HEAT SHIELD, TOP .
Refer to INSTALLING THE LEFT INTAKE SILENCER BRACKET .
Refer to INSTALLING THE LEFT LAMBDA OXYGEN SENSOR .
Refer to INSTALLING THE RIGHT LAMBDA OXYGEN SENSOR .
Refer to INSTALLING THE RIGHT INTAKE SILENCER HOUSING .
Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
Refer to INSTALLING ACOUSTIC COVER .
Refer to INSTALL EXHAUST SYSTEM .
Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
Refer to INSTALLING THE REAR LEFT AND RIGHT TENSION STRUT .
Refer to INSTALLING THE LEFT AND RIGHT UNDERSHIELD (TANK COVER) .