Remount the rain-light-solar-condensation sensor.

Carefully clean new windshield in the contact area (1) of the rain-light-solar-condensation sensor.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: RISK OF DAMAGE
Damage to silicone surface .
A damaged silicone surface can lead to malfunctioning of the rain-light-solar condensation sensor .

Do not tap or damage the silicone coated surface on the rain-light-solar condensation sensor.
After loosening lock, wait approx. 30 min. at 20°C for silicone surface to relax.

Courtesy of BMW OF NORTH AMERICA, INC.

Release the rain-light-solar-condensation sensor (2) from the retaining spring (3).
To do this, press in on both sides of the retaining springs (3), insert the screwdriver (4) to the side and lift up the detent.
Slowly detach the rain-light-solar-condensation sensor (1) from the holder (2) in the direction of the arrow and simultaneously monitor the release of silicone surface from the outside.
The silicone surface must evenly loosen from the windshield, if required, detach slower.

Courtesy of BMW OF NORTH AMERICA, INC.

Checking the gel pad

Check

Check the silicone-coated surface (1) and the PCB (2) for damage.

Courtesy of BMW OF NORTH AMERICA, INC.

Result

» The silicone-coated surface (1) is damaged.

Measure

Replace the gel pad.

Result

» PCB (2) is damaged.

Measure

Replace rain-light-solar-condensation sensor.

Replacing the gel pad

NOTE: RISK OF DAMAGE
Damage to the surface .
The use of sharp-edged tools can damage the surface .

Only use microfiber cloths.

Pull off the gel pad (1) manually.
Do not touch or damage the PCB (2).
Remove present residual gel using a microfiber cloth.

Courtesy of BMW OF NORTH AMERICA, INC.
Clean the surface of the rain-light-solar condensation sensor with a microfiber cloth soaked in a solvent cleaner R2.

CONSUMABLE SPECIFICATIONS

Cleaning agent R2

500 ml

83190417324

Pull off the yellow protective film (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Apply the gel pad (1) centered on the surface of the rain-light-solar-condensation sensor (2).
Do not squeeze out any air pockets present.

Air pockets disappear within 30 minutes after mounting the sensor to the windscreen.

Courtesy of BMW OF NORTH AMERICA, INC.
Pull off the protective film (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Feed the rain-light-solar and condensation sensor (1) into the holder (2) on the new windshield in the direction of the arrow.

Courtesy of BMW OF NORTH AMERICA, INC.
Centrally press on the rain-light-solar-condensation sensor (2) onto the retaining spring (3).
To lock, consecutively press down both sheet metal tabs (4) on every side.

Courtesy of BMW OF NORTH AMERICA, INC.
Check field of view for air pockets.
Visible shading (1) and (2) do not represent air pockets, but indicate the optical element of the sensor. This is not a functional limitation.

Courtesy of BMW OF NORTH AMERICA, INC.

Carefully clean new windshield in the contact area (1) of the rain-light-solar-condensation sensor.

Courtesy of BMW OF NORTH AMERICA, INC.
Slowly detach the rain-light-solar-condensation sensor (1) from the holder (2) in the direction of the arrow and simultaneously monitor the release of silicone surface from the outside.
The silicone surface must evenly loosen from the windshield, if required, detach slower.

Courtesy of BMW OF NORTH AMERICA, INC.

Checking the gel pad

Check

Check the silicone-coated surface (1) and the PCB (2) for damage.

Courtesy of BMW OF NORTH AMERICA, INC.

Result

» The silicone-coated surface (1) is damaged.

Measure

Replace the gel pad.

Result

» PCB (2) is damaged.

Measure

Replace rain-light-solar-condensation sensor.

Replacing the gel pad

NOTE: RISK OF DAMAGE
Damage to the surface .
The use of sharp-edged tools can damage the surface .

Only use microfiber cloths.

Pull off the gel pad (1) manually.
Do not touch or damage the PCB (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Remove present residual gel using a microfiber cloth.
Clean the surface of the rain-light-solar condensation sensor with a microfiber cloth soaked in a solvent cleaner R2.

CONSUMABLE SPECIFICATIONS

Cleaning agent R2

500 ml

83190417324

Pull off the yellow protective film (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Apply the gel pad (1) centered on the surface of the rain-light-solar-condensation sensor (2).
Do not squeeze out any air pockets present.

Air pockets disappear within 30 minutes after mounting the sensor to the windscreen.

Courtesy of BMW OF NORTH AMERICA, INC.
Pull off the protective film (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Feed the rain-light-solar and condensation sensor (1) into the holder (2) on the new windshield in the direction of the arrow.

Courtesy of BMW OF NORTH AMERICA, INC.
Centrally press on the rain-light-solar-condensation sensor (2) onto the retaining spring (3).
To lock, consecutively press down both sheet metal tabs (4) on every side.

Courtesy of BMW OF NORTH AMERICA, INC.
Check field of view for air pockets.
Visible shading (1) and (2) do not represent air pockets, but indicate the optical element of the sensor. This is not a functional limitation.

Courtesy of BMW OF NORTH AMERICA, INC.