Check the timing of cylinder bank 1

• Turn the engine at the central bolt in clockwise direction until the installation position (MP) (1) of the vibration absorber (1) is positioned flush with the marks of the engine block.

Courtesy of BMW OF NORTH AMERICA, INC.

• Check the camshaft positions of cylinder bank 1.

The cams (1) should be in the position shown.

The increment wheels (2) should each form a straight line with the exhaust camshaft bearing cap and the intake camshaft bearing cap.

Courtesy of BMW OF NORTH AMERICA, INC.

Courtesy of BMW OF NORTH AMERICA, INC.

• Make sure that the ground surfaces of the camshafts (1) point upward.
• Take care that the rounded surfaces (1) point down to the cylinder head.
• Check timing again and assess.

• Relieving the chain tensioner at cylinder bank 1 for checking or setting the valve timings 

• Make sure that the chain drive is loaded at the same time on the central bolt of the engine and on the VANOS central valve on the exhaust  .

The movement of the chain tensioner piston must be observed in this process.

To do this, the following steps must be carried out at the same time:

• Keep the VANOS central valve on the exhaust under tension in clockwise direction with a support person.

The VANOS central valve on the exhaust must not be twisted.

Courtesy of BMW OF NORTH AMERICA, INC.

• Turn engine counter clockwise at central bolt (1).

Courtesy of BMW OF NORTH AMERICA, INC.

• Slackening the hydraulic chain tensioner of cylinder bank 1 

Courtesy of BMW OF NORTH AMERICA, INC.

• Position the special tool 0 491 012 (11 4 120) (3) in the bore and fasten the chain tensioner piston.

• Make sure that the chain drive is relieved at the same time on the central bolt of the engine and on the VANOS central valve on the exhaust  . To do this, carry out the following steps at the same time:

• Relieve the chain drive clockwise at the central bolt.

Courtesy of BMW OF NORTH AMERICA, INC.

• Relieve the chain drive counterclockwise at the VANOS central valve on the exhaust.

Courtesy of BMW OF NORTH AMERICA, INC.

Courtesy of BMW OF NORTH AMERICA, INC.

• Loosen screws (1).
• Feed out and remove hydraulic chain tensioner (2).
• Unscrew the screw (2) until the special tool 2 249 162 is slackened.
• Position the special tool 2 249 162 on the cylinder head and apply the screws (1) hand-tight.
• Hand-tighten the bolts (1).
• Pre-tension timing chain on special tool 2 249 162 at hexagon screw (2) with special tool 0 496 778 (00 9 460) to 0.6 Nm.

Preload timing chain
Tightening torque	0.6 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

• Position special tool 0 496 366 (11 8 570) (3) on the vibration absorber.
• Position special tool 0 493 882 (11 9 190) (1) in special tool 0 496 366 (11 8 570).

• Position reversible ratchet.
• Rotate the engine on the central bolt clockwise until the special tool lines up with the engine block marks.
• Attach the special tool 0 496 366 (11 8 570) (3) to the vibration absorber with a screw from the belt pulley (2) and hand-tighten.
• With the crankshaft in the installation position, use the special tool 0 493 882 (11 9 190) (1) to insert it onto the marks and fasten.

Courtesy of BMW OF NORTH AMERICA, INC.

Courtesy of BMW OF NORTH AMERICA, INC.

• Make sure that the ground surfaces of the camshafts (1) point upward.
• Take care that the rounded surfaces (1) point down to the cylinder head.
• Check timing again and assess.

Check 

• Check the camshaft positions of cylinder bank 1.

The cams (1) should be in the position shown.

The increment wheels (2) must be flush with the exhaust camshaft bearing cap and the intake camshaft bearing cap.

The ground surfaces of the camshaft must face up.

Courtesy of BMW OF NORTH AMERICA, INC.

Result 

» Camshaft position is correct.

Measure

• Continue the repair with the next step.

Result 

» Camshaft position is not correct.

Measure

• Disassemble special tools 0 496 366 (118 570) and 0 493 882 (11 9 190)  and remove.

Measure

• Turn engine at the central bolt of the crankshaft by 360° until the installation position (MP) of the vibration absorber is positioned flush with the marks of the engine block.

Measure

• Re-secure the engine in TDC setting with special tools 0 496 366 (118 570) and 0 493 882 (11 9 190)  .

Check 

• Position special tool 2 249 117 (1) on the camshafts of cylinder bank 1.
• Check if the camshafts can be fastened with the special tool 2 249 117 (1).
• Check if the special tool 2 249 117 can be brought in contact with the cylinder head using the two screws of the cylinder head cover (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Result 

» The camshafts can be fastened.

Measure

• Loosen screws (2).

Remove the special tool 2 249 117 (1).

Continue the repair in the next step.

Result 

» The camshafts cannot be fastened.

Measure

• Adjust the timings of cylinder bank 1.

• Release timing chain on the special tool 2 249 162 by turning the hexagon screw (2).
• Release special tool 2 249 162 in area (1) and remove.

Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and position the hydraulic chain tensioner (2).
• Tighten down screws (1).

Chain tensioner to cylinder head
screw	Tightening torque	13 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

• Remove the special tool 0 491 012 (11 4 120) (3).

Courtesy of BMW OF NORTH AMERICA, INC.