Install the oil vacuum pump
- Guide out and remove the centering sleeves (1) from the crankcase in the direction of the arrow using standard tools (2).
- Replace the centering sleeves (1).
Parts: Centering sleeves
- Insert and install centering sleeves (1) on the oil vacuum pump (2).
- Position sprocket wheel (1) on oil vacuum pump (2).
The labeling on the sprocket wheel (1) must point away from the oil vacuum pump (2).
- Replace the screw (1).
Parts: Screw
NOTE: TECHNICAL INFORMATION The thread is a left-hand thread. - Guide in and fix the screw (1).NOTE: TECHNICAL INFORMATION Conduct the following operation with the assistance of a second person.
- Counter-hold the sprocket wheel with the special tool 0 491 440 (23 0 020)
and tighten the screw (1) with standard tools (2).TIGHTENING TORQUES SPECIFICATION
Sprocket wheel at the oil vacuum pump M8 Important - left-hand thread Replace screw. Joining torque 5 Nm Angle of rotation 90° - Insert and position the oil vacuum pump (1) in the drive chain (2).
- Replace screws (1).
Parts: screw
- Tighten down screws (1).TIGHTENING TORQUES SPECIFICATION
Oil vacuum pump to crankcase M8 Replace screw. Joining torque 15 Nm Angle of rotation 45°
Follow-up work
- Refer to REFITTING ENGINE OIL PAN .
- Refer to INSTALLING BEARING BRACKET
- Refer to INSTALLING FRONT AXLE DIFFERENTIAL .
- Refer to SECURING THE JUNCTURE SHAFT IN FRONT ON THE FRONT AXLE DIFFERENTIAL .
- Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL PAN .
- Refer to REPLACING THE LEFT AND RIGHT RADIAL SHAFT SEAL .
- Refer to INSTALLING THE FRONT AXLE SUPPORT (RAISE) AND FASTEN .
- Refer to INSTALLING OUTPUT SHAFT ON LEFT AND RIGHT .
- Refer to TOPPING UP/CHECKING FRONT AXLE TRANSMISSION OIL .
- Refer to ATTACHING THE RIGHT AND LEFT TENSION STRUTS ON THE SWIVEL BEARING .
- Refer to SECURING THE WISHBONE ON THE LEFT AND RIGHT ON THE SWIVEL BEARING .
- Refer to ATTACHING THE RIGHT AND LEFT OUTPUT SHAFT ONTO THE WHEEL BEARING .
- Refer to SECURING THE TIE ROD TO THE RIGHT AND LEFT ON THE SWIVEL BEARING .
- Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR .
- Refer to FASTEN ELECTRIC COOLANT PUMP AND COOLANT HOSES TO THE FRONT AXLE SUPPORT
- Refer to IF INSTALLED: CONNECT THE VACUUM LINE OF THE ENGINE MOUNTS .
- Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR
- Refer to SECURING THE EPS WIRING HARNESS TO THE ELECTROMECHANICAL STEERING GEAR .
- Refer to INSTALLING STEERING SHAFT AT BOTTOM ON STEERING GEAR
- Refer to INSTALLING THE COVER PANELS ON THE FRONT AXLE ON THE RIGHT AND LEFT .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
- Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION
- Refer to INSTALLING FUEL DELIVERY LINE .
- Refer to INSTALLING ALL IGNITION COILS .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING THE COWL UPPER PART .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE SEAL FOR THE HOOD GASKET LEFT AND RIGHT .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
- Refer to INSTALLING RESONATOR .
- Refer to INSTALLING INTAKE FILTER HOUSING .
- Refer to INSTALLING THE RIGHT FRONT-END STRUT .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to FILLING ENGINE OIL
- Refer to OPENING THE OIL FILLER CAP
- Refer to RECONNECTING ALL BATTERY GROUND LEADS
- Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
- Refer to CHECKING ENGINE OIL LEVEL .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING THE FRONT UNDERBODY PROTECTION .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .