54 10... Repair notes for bonded seals (330i xDrive Wagon, 328d xDrive Wagon, 330i GT xDrive, 340i GT xDrive)

WARNING: This page does not describe the selected car, but rather 11 other vehicles, including the 2019 BMW 340i GT xDrive, 2019 BMW 330i xDrive, 2019 BMW 330i GT xDrive, 2018 BMW 340i GT xDrive, and 2018 BMW 330i xDrive. However, it is still accessible from the selected car via links, so may be relevant.

Required special tools:

00 9 327

1 General remarks on handling rubber seal profiles:

If seals reveal partly detached protective film on delivery, they must not be bonded.
Store seals at 5°C to 40°C.
If, during the handling, the protective film has come off before bonding, it can still be bonded.
Bonding at room and object temperature 25° ± 5° C. Temperatures between 40 and 50°C significantly increase initial adhesion.
Seals, which are subjected to temperatures above 80°C after bonding, will be very difficult to remove.
Maximum storage time for replacement: see identification of the expiry date on packaging

2 Damage, repair and replacement

A partially released bonding (rubber component, adhesive tape or adhesive tape paint) up to 120 mm may be finished. Continue with Point 2.1.

A partially released bonding (rubber component, adhesive tape or adhesive tape paint) above 120 mm may not be finished. Gasket must be replaced. Continue with Point 2.2.

2.1 Repair of partially released bonding (rubber component, adhesive tape or adhesive tape paint

2.1.1 Clean faulty areas

Release adhesive area of paint side from recesses and degrease with CLEANING AGENT R2 . Stick to air drying time > of 1 minute. Never use paint thinner!
This will usually partially destroy intact edge adhesive areas.
When removing, it is important to wipe off the adhesive area of the adhesive tape with a lint-free disposable cloth. (e.g. blue Kimtex)
Carefully wipe off the adhesive areas.

NOTE: Use necessary cotton- or fluff-free paper towel once only.

NOTE: Do not touch the adhesive area after cleaning.

2.1.2 Apply adhesive

Apply RUBBER ADHESIVE evenly as a thin layer first on the gasket and then on the painted surface.
Stick to air drying time of 2 to 3 minutes.

Attention:

Avoid contact with skin!

Do not apply adhesive to visible painted surfaces.

2.1.3 Press in rubber seal

Press down gasket using contact pressure (forced pressure not necessary) for > 1 minute.

Attention:

Load can be applied to the bonding only after a period of 2 minutes. This waiting time is absolutely essential.

2.2 Replacement

2.2.1 Peeling off the faulty rubber seal

Courtesy of BMW OF NORTH AMERICA, INC.

Remove bonded connection with fingers or cleaning agent liner 00 9 327.
Overstretch gasket below an angle of maximum 20° very slowly under even tensile stress.
If the gasket is detached too quickly, the adhesive tape can tear off and remain on the painted surface.

The adhesive tape remaining on the painted surface must be removed with high cleaning costs.

NOTE: When the adhesive tape separates from the gasket, the adhesive tape remaining on the paint must be fully separated at one location by approx. 10 mm until it is easy to grip.

Detach the adhesive tape by pulling strongly at an angle of approx. 20°.

When existing gaskets are being peeled off with a hot air blower: Do not damage paintwork.

2.2.2 Clean bonding surface

If required, remove adhesive remains with ERASER DISK or CLEANING AGENT R2 . do not damage paint. Stick to air drying time > of 1 minute.
Before a new bond, treat the entire adhesive area with SIKA AKTIVATOR 205 . Stick to air drying time > of 1 minute.

NOTE: Use necessary cotton- or fluff-free paper towel once only.

Do not touch the adhesive area after cleaning.

2.2.3 Detach protective film of the bonding surface

Detach the protective film off of the new gasket by approx. 15 cm using the lug.

Attention:

Once the protective film has been removed, do not under any circumstances touch the exposed bonding surface.

2.2.4 Apply rubber seal

Manually press on the gasket continuously while detaching the liner slightly at the same time.

NOTE: If positioned incorrectly, the gasket can still be detached, repositioned and pressed on again.
Always ensure that you do not touch the bonding surface with your fingers or contaminate it in any way.

Press gasket while shifting in a straight line without compression or over-stretching.
Compress the gasket the corners; never stretch it. (critical area)

2.2.5 Establish sealing joint

Where the beginning and end meet, a mark is created from pressing the loose end onto the beginning of the gasket.
Cut off the gasket vertically along the marked line (use sharp knife or special scissors) and press in place.
Visually check the pre-bonded gasket.

NOTE: Small areas of gasket can remain stuck to adhesive tape of loose end.

2.2.6 Press gasket

Always press gasket vertically to the bonding surface
Manually press gasket or hand roller
Adhesive tape width up to 5 mm, contact pressure > 5 N/cm
Adhesive tape width up to 10 mm, contact pressure > 10 N/cm

NOTE: Firm thumb pressure has approx. 35 N/cm

3 Checking the rubber seal

Check the bonded gaskets for correct positioning and perfect adhesion. The bonding can be checked by pressing back the sealing lip.
The peel strength of the gasket must be greater than 10 N/cm for about 15 min after bonding.