Install rear trim panel
- Check whether the clips (1) are present and have damage.
Damaged or missing clips (1) must be replaced.
- Install the side trim panel and in this process insert the safety belt.
- Connect all connectors (1) and lock.
- Position side trim panel (1) correctly and guide it into the edge protection carefully.
- Clip side trim panel (1) into clamps (2).
- Clip side trim panel (1) into clips (3).
- Tighten screws (1) and (2).TIGHTENING TORQUE SPECIFICATION
Side finisher panel, rear Cheese head screw (sheet metal screw) Tightening torque 3.2 Nm M6x25 screw Tightening torque 3.2 Nm - Tighten down screw (1).TIGHTENING TORQUE SPECIFICATION
Side finisher panel, rear Cheese head screw (sheet metal screw) Tightening torque 3.2 Nm M6x25 screw Tightening torque 3.2 Nm - Tighten down screw (1).TIGHTENING TORQUE SPECIFICATION
Rear side trim panel (on the seat-belt extender) Torx bolt Tightening torque 1.8 Nm - Install the cover (1).
Installing seat belt extender hand
NOTE:
TECHNICAL INFORMATION
Clean all threaded belt connections with micro-encapsulated outer and internal threads.
Shavings or other debris must not remain in the components.
If a microencapsulated screw is reused, it must be coated with the following screw locking agent: Loctite 243, medium strength .
The screw connection must be completed within 10 minutes as hardening begins after this period.
Clean all threaded belt connections with micro-encapsulated outer and internal threads.
Shavings or other debris must not remain in the components.
If a microencapsulated screw is reused, it must be coated with the following screw locking agent: Loctite 243, medium strength .
The screw connection must be completed within 10 minutes as hardening begins after this period.
NOTE:
To provide a better overview: Schematic diagram with partially hidden components.
- Thread the shoulder belt (3) into the seat belt extender hand (1).
- Carefully feed the seat belt extender hand (1) into the seat belt extender (2) in the arrow direction.
Installing the front strap fitting
NOTE:
TECHNICAL INFORMATION
Clean all threaded belt connections with micro-encapsulated outer and internal threads.
Shavings or other debris must not remain in the components.
If a microencapsulated screw is reused, it must be coated with the following screw locking agent: Loctite 243, medium strength .
The screw connection must be completed within 10 minutes as hardening begins after this period.
Clean all threaded belt connections with micro-encapsulated outer and internal threads.
Shavings or other debris must not remain in the components.
If a microencapsulated screw is reused, it must be coated with the following screw locking agent: Loctite 243, medium strength .
The screw connection must be completed within 10 minutes as hardening begins after this period.
- Clip in the cover (2) of the seat belt end fitting (3) in arrow direction in the seat belt end fitting (3).
- Slide the sleeve (1) in the cover (2) of the seat belt end fitting (3).
- Position the seat belt end fitting correctly.
- Tighten down screw (2).TIGHTENING TORQUE SPECIFICATION
End lining to body M10 Tightening torque 42 Nm - Clip in the cover cap (1).
Follow-up work
- Refer to INSTALLING THE UPPER TRIM PANEL ON ROLLOVER PROTECTION SYSTEM .
- Refer to INSTALLING THE REAR LEFT AND RIGHT HEAD RESTRAINT GUIDES .
- Refer to INSTALLING REAR LEFT AND RIGHT HEAD RESTRAINTS .
- Refer to REMOVING REAR SEAT BACKREST .
- Refer to INSTALLING THE LEFT AND RIGHT BACKREST SIDE SECTION .
- Refer to INSTALLING THE REAR SEAT .
- Refer to INSTALLING THE INNER DOOR SILL COVER STRIP .
- Refer to ATTACHING THE REAR OUTER WINDOW RECESS FINISHER STRIP .