Removing the intake plenum

WARNING: Working on 12 V electrical system .
Risk of short circuits! Risk of fire!

Make sure that there is no charger connected to the jump start terminal in the engine compartment.
Detach battery ground lead from battery.
For auxiliary batteries: Detach battery minus cables from all auxiliary batteries.

NOTE: RISK OF DAMAGE
Damage to battery terminal, the safety battery terminal or the intelligent battery sensor (IBS) .
Damaged battery terminals can lead to malfunctions or vehicle electrical system faults .

Detach battery terminal from battery pole by carefully shifting to and fro. Do not pry off using a tool.

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

Preliminary work

Refer to BRINGING FRONT COMPARTMENT LID IN THE SERVICE POSITION .
Refer to DISCONNECTING ALL BATTERY GROUND LEADS .
Refer to REMOVING SUSPENSION STRUT BRACE .
Refer to REMOVING THE ACOUSTIC COVER .
Refer to REMOVING THE FRONT-END STRUT .
Refer to REMOVING THE CLEAN AIR PIPE FOR CYLINDERS 1 TO 3 .
Refer to REMOVING THE LEFT INTAKE FILTER HOUSING (FRONT-END STRUT REMOVED) .
Refer to REMOVING THE RIGHT INTAKE FILTER HOUSING (FRONT-END STRUT REMOVED) .
Refer to REMOVING THE COVER FOR THE DME CONTROL UNIT .
Refer to REMOVING THE DME CONTROL UNIT .
Refer to REMOVING THE INTEGRATED SUPPLY MODULE (PDM) PARTIALLY .
Refer to REMOVING THE CONTROL UNIT HOLDER .
Refer to REMOVING SEAL FOR FRONT HOOD .
Refer to REMOVING THE COVER FOR THE CENTER ENGINE COMPARTMENT .
Refer to REMOVING UPPER CROSS CONNECTION .
Refer to REMOVING THE REAR TOP CROSS CONNECTION .
Refer to REMOVING THE FRONT SPOILER .
Refer to REMOVING THE FRONT UNDERBODY PROTECTION .
Refer to REMOVING THE LEFT AND RIGHT FRONT UNDERSHIELD .
Refer to REMOVING THRUST FIELD .
Refer to REMOVING THE FRONT BOTTOM SIDE COVER .
Refer to REMOVING THE RIGHT HAND FRONT BOTTOM SIDE COVER .
Refer to PARTIALLY RELEASING THE ENGINE OIL COOLER .
Refer to DRAINING THE COOLANT FOR THE HIGH-TEMPERATURE COOLANT CIRCUIT .
Refer to DRAINING THE COOLANT FROM THE LOW-TEMPERATURE COOLING SYSTEM .
Refer to CONNECTING THE COOLANT LINE TO THE RADIATOR .
Refer to CONNECTING THE COOLANT LINES FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
Refer to REMOVING THE COOLANT EXPANSION TANK FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
Refer to REMOVING THE FAN COWL .

Screws of the intake plenum

Fig 1: Intake Plenum Screws Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: RISK OF DAMAGE
Damage to wires when disconnecting connectors and plug connections .
Sheared wires can cause a short circuit .

Do not pull on wires when disconnecting connectors and plug connections.

NOTE: TECHNICAL INFORMATION
Collect and dispose of emerging fluids. Observe country-specific waste disposal regulations.

NOTE: TECHNICAL INFORMATION
Additional coolant can leakage. Make sure that no coolant enters the intake port of the cylinder head.

Loosen screws (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Feed out the charge air crossing (2) and place to one side.

Courtesy of BMW OF NORTH AMERICA, INC.
Release nut (1).
Guide out the electrical auxiliary coolant pump (2) and set it aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Release the holder (1) from the electrical auxiliary coolant pump (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock plug connection (1) and disconnect.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock the clamp (1) and engage it in this position.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock the clamp (1).
Detach charge air hose (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock the locks (arrows).
Remove the wiring harness section (1) and put to one side.

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock plug connection (1) and disconnect.
Unlock the locks (2).
Detach the tank vent line with pressure sensor (3).

Courtesy of BMW OF NORTH AMERICA, INC.
Release tank vent line (1) from clamps (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock the lock (1).
Remove the wiring harness section (2) and put to one side.

Courtesy of BMW OF NORTH AMERICA, INC.
Release nut (1).
Guide out tank vent line (3) from holders (2) and keep it aside.

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen clamp (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock plug connection (1) and disconnect.
Release clamps (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Loosen screws (1).
Guide out and remove holder (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock and remove the coolant line (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock and remove the coolant line (1).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock coolant lines (1) and pull off.
Unlock and detach the tank vent line (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Unlock plug connection (1) and disconnect it from throttle valve (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Release clamps (1) from charge air cooler (2) in the marked area.

Courtesy of BMW OF NORTH AMERICA, INC.
Release the screws in the sequence (7) to (1).
Guide out and remove charge air cooler (A) carefully .

Fig 2: Charge Air Cooler Screws Loosening Sequence
Courtesy of BMW OF NORTH AMERICA, INC.
Empty the remaining coolant (2) from the intake plenum (1).

Courtesy of BMW OF NORTH AMERICA, INC.