Service Action: Replace Drive Belt Idler Pulley Bracket (SI B11 02 24)
Publication date: 2024-07-16Reference number: SI B11 02 24
SERVICE ACTION: REPLACE DRIVE BELT IDLER PULLEY BRACKET
SERVICE CAMPAIGN BULLETIN
| BMW: | G80 M3 Sedan; G82 M4 Coupe; G83 M4 Convertible; G87 M2 Coupe |
SERVICE INFORMATION
Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop.
AFFECTED VEHICLES
- Vehicles which require this campaign to be completed will show it as "Open" when checked either in AIR, AWP, Campaign Summary, or Warranty Vehicle Inquiry.
- Please make sure you check your dealer inventory as soon as possible. You can see a list of affected vehicles in Inventory Campaign Details (ICD) under ROSS.
SITUATION
The drive belt idler pulley bracket material does not have adequate hardness and the attaching bolts may loosen.
PROCEDURE
- Remove the idler pulley for the drive belt (1) as described in Repair Instruction 11 28 025 "Replacing idler pulley for drive belt of alternator."
Loosen the bolts and remove the idler pulley bracket (2).
- Replace the bracket with bolts and tighten them to 10 Nm.
- Re-install the idler pulley for the drive belt as described in Repair Instruction 11 28 025 "Replacing idler pulley for drive belt of alternator."
PARTS INFORMATION
Use and invoice the applicable part numbers listed below.
| Part Number | Description | Series | Quantity |
|---|---|---|---|
| 11 28 8 091 448 | Bracket, idler pulley | All | 1 |
| 11 51 9 908 732 | Hexagon bolt | All | 2 |
| 11 28 8 469 699 | Spacer bolt | All | 1 |
| 11 28 7 795 159 | Protective cap | All | 1 |
| 07 14 7 270 121 | Torx bolt with collar | G87, G83, G82, G80 | 4 |
| 07 11 9 904 956 | Hexagon bolt | G87, G83, G82, G80 | 1 |
| 07 14 8 086 257 | Hexagon bolt | G87, G83, G82, G80 | 5 |
| 07 14 7 381 866 | Hexagon nut with washer | G87, G83, G82, G80 | 8 |
| 07 14 7 883 031 | Multi-purpose bolt | G87, G83, G82, G80 | 2 |
| 07 14 9 502 134 | Multi-purpose bolt | G87, G83, G82, G80 | As needed, up to 17 |
SUBLET - BULK SUPPLY MATERIALS
| Part Number | Description | Quantity |
|---|---|---|
| 83 19 5A32851 | HT-12 Antifreeze RTU (Bulk DN = 1/10 Liter) (Pre-mix) | As needed |
| Or: | ||
| 83 19 2468442 | BMW Antifreeze/Coolant (DN = 1 Gallon Concentrate) - HT-12 | As needed |
Additionally, other materials and small parts that are not specified above, such as fluids, lubricants, one-time use screws nuts, and seals, which must be replaced or installed (according to the ISTA repair instructions/ETK/AIR), are to be selected from the Electronic Parts Catalog and/or other approved BMW Group resources according to the respective vehicle type. Invoiced these items separately under the Repair Code listed in this bulletin.
CLAIM INFORMATION
Reimbursement for this Service Action will be via normal claim entry utilizing the applicable work package information below and the part numbers above that apply.
| Repair Code: | 0011730700 | G8x Replacing deflecting element holder |
Below are the special flat rate labor operation code choices for this action.
Completion before the first vehicle delivery to a customer or the vehicle is already in the workshop.
| Work Pkg | Labor Operation | Description (Plusposition work) | Labor Allowance |
|---|---|---|---|
| # 1 | 00 76 798 | Replacing the idler pulley bracket | 50 FRU (G80); 51 FRU (G82, G83); 63 FRU (G87) |
Or:
The vehicle arrives at your center and this Service Action shows open (No other Main work will be performed or claimed during this workshop visit).
| Work Pkg | Labor Operation | Description (Main work) | Labor Allowance |
|---|---|---|---|
| # 2 | 00 76 186 | Replacing the idler pulley bracket | 52 FRU (G80); 53 FRU (G82, G83); 65 FRU (G87) |
Only one of the flat rate labor operation codes listed above can be used for claim submission and reimbursement. Also, only one Main work flat rate labor operation code can be claimed per workshop visit.
CLAIM REPAIR COMMENTS
Only reference the SIB number and the work package (Pkg) number performed in the RO technician notes and the claim comments (For example: B11 02 24 WP 1), unless otherwise required by State law.
SUBLET - BULK SUPPLY MATERIALS (RO AND CLAIM COMMENTS REQUIRED)
| Sublet Code 4 | Reimbursement for the repair-related bulk supply material (Do not use the BMW part number for claim submission) | Up to $50.00 |
Sublet reimbursement calculation for claiming the applicable repair-related bulk supply material (BMW part number) is at the dealer net price amount for the proportional quantity used plus your center's handling.
BMW Antifreeze/Coolant: Claim the corresponding sublet dollar amount for the quantity needed to replace what was drained. The one-gallon concentrate part number quantity for a 50/50 coolant/water solution.
Enter this material cost in sublet and itemize the amount on the repair order and in claim comment section.
ALTERNATIVE MOBILITY SOLUTION (AMS) FOR VEHICLE OWNERS (RO AND CLAIM COMMENTS REQUIRED)
This Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement, claim this item under the Defect Code noted above as follows:
- Sublet Code 2 - Itemize the AMS sublet amount on the repair order and in the claim comment section.
Please refer to SI B01 29 16 for additional information.
FEEDBACK REGARDING THIS BULLETIN
| Technical Feedback | To submit feedback for the technical topic of this bulletin: Submit your feedback in the rating box at the top of this bulletin |
| Warranty Feedback | To submit feedback for the CLAIMS section of this bulletin: Submit an IDS ticket to the Warranty Department, or use the chat available in the Warranty Documentation Portal |
| Parts Feedback | To submit feedback for the PARTS section of this bulletin: Submit an IDS ticket to the Parts Department |